background image

9

Operating the machine:

Before starting the machine:

Put the desired tool into the bowl and place the bowl in the 
bowl arms.

Turn the tool to lock it into the bayonet fitting.

Fit the safety guard.

Lift the bowl with the aid of the lifting handle. 

The mixer is now ready to start.

It is possible to set both the running time and speed before 

starting the machine; see next section:

Start the machine:

Press 

 to start the mixer.

Press 

 next to 

 to increase the speed.

Press 

 next to 

 to reduce the speed.

The speed is shown as a number on the scale 

12345678

.  

The display 

12345678

 represents the lowest speed, 

approx. 72 rpm.

The display 

12345678

 represents the highest speed, 

approx. 450 rpm.

If a specific start speed is wanted, you set the speed and 
then start the mixer by pressing 

.

Display of running time – Timer function:

Select a running time for the mixer by pressing 

 next to 

. The running time is shown in minutes and seconds in 

the timer field between 

 and 

.

Running times of up to 90 minutes are available.

When the mixer is running, the running time will not be reset 

if 

 is pressed once; press 

 once more and it will be 

reset.

If no running time is selected, the display will show the time 

elapsed since the mixer was started.

If the time set on the timer runs out while the mixer is run

-

ning, the mixer stops and you hear a bib.

Inspection of ingredients while in use:

If the mixer needs to be stopped temporarily without affec

-

ting the running time, press 

. The mixer will slow down 

and then stop and the running time will stop too. 

The bowl can now be lowered and the ingredients checked.

Lift the bowl and press 

, and the mixer will start and the 

running time will resume. 

Stop the machine:

To stop the machine:
•  Press 

. Running time not reset.

•  Press 

 twice. Running time reset.

Restart by pressing 

.

It will start at the lowest speed.

The emergency stop - only to be used in emer-

gency situations and for powering off the mixer

Emergency stop

Stop

Increase time

Timer (timer field)

Decrease time

Speed indi-

cator

Decrease speed

Increase speed

Start

Summary of Contents for KODIAK10

















Reviews: