background image

 

POWX139 

EN

 

Copyright © 2014 VARO 

P a g e

 | 

11

 

www.varo.com 

12 WARRANTY 

 

This product is warranted for a 36-month period effective from the date of purchase by the 

first user. 

 

This warranty covers all material or production flaws excluding : batteries, chargers, 

defective parts subject to normal wear & tear such as bearings, brushes, cables, and 
plugs, or accessories such as drills, drill bits, saw blades, etc. ; damage or defects 
resulting from maltreatment, accidents or alterations; nor the cost of transportation. 

 

Damage and/or defects resulting from inappropriate use also do not fall under the 

warranty provisions. 

 

We also disclaim all liability for any bodily injury resulting from inappropriate use of the 

tool. 

 

Repairs may only be carried out by an authorized customer service center for Powerplus 

tools. 

 

You can always obtain more information at the number 00 32 3 292 92 90. 

 

Any transportation costs shall always be borne by the customer, unless agreed otherwise 

in writing. 

 

At the same time, no claim can be made on the warranty if the damage of the device is 

the result of negligent maintenance or overload. 

 

Definitely excluded from the warranty is damage resulting from fluid permeation, 

excessive dust penetration, intentional damage (on purpose or by gross carelessness), 
inappropriate usage (use for purposes for which the device is not suitable), incompetent 
usage (e.g. not following the instructions given in the manual), inexpert assembly, 
lightning strike, erroneus net voltage. This list is not exhaustive. 

 

Acceptance of claims under warranty can never lead to the prolongation of the warranty 

period nor commencement of a new warranty period in case of a device replacement. 

 

Devices or parts which are replaced under the warranty  therefore remain the property of 

Varo NV. 

 

 We reserve the right to reject a claim whenever the purchase cannot be verified or when 

it is clear that the product has not been properly maintained. (Clean ventilation slots, 
carbon brushes serviced regularly, etc.). 

 

Your purchase receipt must be kept as proof of date of purchase. 

 

Your appliance must be returned undismantled to your dealer in an acceptably clean 

state, (in its original blow-moulded case if applicable to the unit), accompanied by proof of 
purchase. 

13 ENVIRONMENT 

Should your appliance need replacement after extended use, do not dispose of it 
with the household refuse, but in an environmentally safe way. 
Waste produced by electrical machine items should not be handled like normal 
household rubbish. Please recycle where recycle facilities exist. Check with your 
Local Authority or retailer for recycling advice. 

Summary of Contents for Powerplus POWX139













Reviews: