background image

 

POWX1730 

EN

 

Copyright © 2015 VARO 

P a g e

 | 

7

 

www.varo.com 

7.4 

On/Off switch (8) 

To switch on the equipment set the On/Off switch (8) to position 1. 
Move the On/Off switch (8) to position 0 to switch off the equipment. 

7.5 

Adjusting the pressure: (Fig. 2) 

You can adjust the pressure on the pressure gauge (6) using the pressure regulator (7). 
The set pressure can be taken from the quicklock coupling (5). 

7.6 

Setting the pressure switch 

The pressure switch is set at the factory. 
Switch-on pressure 6 bar. 
Switch-off pressure 8 bar. 

8  CLEANING AND MAINTENANCE 

Important! Pull the power plug before doing any cleaning and maintenance 
work on the appliance. 

Important! Wait until the compressor has completely cooled down. Risk of 
burns! 

Important! Always depressurize the tank before carrying out any cleaning 
and maintenance work. 

8.1 

Cleaning 

 

Keep the safety devices free of dirt and dust as far as possible. Wipe the equipment with a 
clean cloth or blow it with compressed air at low pressure. 

 

We recommend that you clean the appliance immediately after you use it. 

 

Clean the appliance regularly with a damp cloth and some soft soap. Do not use cleaning 
agents or solvents; these may be aggressive to the plastic parts in the appliance. Ensure 
that no water can get into the interior of the appliance. 

 

You must disconnect the hose and any spraying tools from the compressor before 
cleaning. Do not clean the compressor with water, solvents or the like. 

8.2 

Condensation water 

The condensation water must be drained off each day by opening the drain valve (11) (on the 
floor of the pressure vessel). 

Important! The condensation water from the pressure vessel will contain 
residual oil. Dispose of the condensation water in an environmentally 
compatible manner at the appropriate collection point. 

8.3 

Safety valve (10) 

The safety valve has been set for the highest permitted pressure of the pressure vessel. It is 
prohibited to adjust the safety valve or remove its seal. Actuate the safety valve from time to 
time to ensure that it works when required. Pull the ring with sufficient force until you can hear 
the compressed air being released. Then release the ring again. 

Summary of Contents for POWERPLUS POWX1730











Reviews: