background image

 

POWXQG6060 

EN

 

Copyright © 2015 VARO 

P a g e

 | 

7

 

www.varo.com 

8  ASSEMBLY 

8.1 

Bike handle installation (Fig. 1) 

Install the U-handle on the fixing holder, install the clamp and fasten with the screws. 

8.2 

Installation protection guard (Fig. 2) 

 

Remove the 2 screws from the guard. 

 

Position the guard so it can be fixed into place with the clamp and the screws. 

 

Tighten the screws 

8.3 

Installing the harness (Fig. 3) 

 

Adjust the harness hanger in a comfortable position 

 

Buckle the harness at the hanger 

8.4 

Replace the metal blade to spool 

CAUTION: NEVER use unit if blade is warped or has teeth that are chipped or 
missing. Replace a damaged blade immediately. 

CAUTION: Always wear heavy-duty work gloves when handling and installing 
a blade. 

8.4.1 

Disassembly metal blade 

 

Align the hole on the gear box to the slot on the flange washer 

 

Use the screwdriver to go through the hole and slot, and hold the flange washer 

 

Loose the nut and remove the metal blade and cup washer 

8.4.2 

Assembly spool (Fig. 4) 

 

Install the flange washer and cup washer on the spindle shaft. 

 

Install the spool and tighten it. 

STOP ENGINE IMMEDIATELY! 

Excessive  vibration  of  blade  means  that  it  is  not  properly  installed-stop 
engine  immediately  and  check  blade.  Blade  not  properly  installed  will  cause 
injury. 

9  FUEL AND LUBRICATION 

9.1 

Fuel 

Use regular grade unleaded petrol mixed with 40:1 custom 2-cycle engine oil for best results. 
Use mixing ratios in Section FUEL MIXING TABLE below. 

WARNING:  Never  use  normal  petrol  in  your  unit.  This  will  cause  permanent 
engine damage and void the manufacturer’s warranty for the product.  Never 
use a fuel mixture that has been stored for over 90 days. 

WARNING:  2-cycle  lubricant  must  be  a  premium  grade  oil  for  2-cycle  air 
cooled engines mixed at a 40:1 ratio. Do not use any 2-cycle oil product with a 
recommended  mixing  ratio  of  100:1.  If  insufficient  lubrication  is  the  cause  of 
engine damage, it voids the manufacturer’s engine warranty. 

Summary of Contents for Powerplus XQ POWXQG6060















Reviews: