background image

 

2

 

 

 
 
 

 

 

CONTROL PANEL 

 

High steam level indicator

Lack of water indicator

Descaling indicator

Medium steam level indicator

Low steam level indicator

Power indicator

Steam level control button

(for increasing steam)

Steam level control button

(for decreasing steam)

Power button

 

 
 

Filling aperture cap 

The filling cap is attached in the water tank, if less water in the tank, you shall open the cap and fill water. After filling 
water, close it. 

 

Front & Rear support 

You can put the iron on the front & rear support during operation and you can also secure the iron into front & rear 

support for storage after finishing ironing. 

   

Power switch 

Plug in the appliance and press down the Power switch, the power indicator will be illuminated, also the low steam rate 

regarded as defaulted one and its indicator will flash. Press down the Power switch for a while, both the power indicator 
and low rate steam indicator will be extinguished, and the appliance will be disconnected from the power supply. 

 

Steam level control buttons   

The steam rate can be selected low, medium or high with the two steam rate control buttons (see the schematic 

illustration of Control panel). Any one to be selected, its indicator will flash, after a few minutes, the indicator will be 

changed to illuminating. At this time, the appliance can produce steam, you can use the steam for ironing. 
 

Temperature dial 

Turn the dial to set ironing temperature to meet the garment changed. E.g. rotate the dial to 

select the second temperature setting. See the point indicated by an arrow shown in the figure as below.   

 

 

 

 

Temperature indicator

 

When the iron is heating up, the temperature indicator will be illuminated. Once the iron has reached the selected 
temperature, it will extinguish. The temperature indicator will be cycled on and off as the iron maintains the selected 

temperature during ironing.   

 

Steam trigger 

After pressing down the Power switch and choosing the desired steam rate, it indicates the steam can be used for 

ironing until the steam rate indicator is changed flashing to illuminating. At this time, press the steam release button 

Summary of Contents for Stiroplus SP 1079
















Reviews: