background image

Vastex E-mail assistance 

  
Purchasing, product and printing Info: 

sales@vastex.com 

  

Electrical Support: 

stech@vastex.com 

  

Tech Support, Mechanical Setup, and Operation: 

techsupport@vastex.com

 

Vastex International, Inc. 
7 Emery Street 
Bethlehem, PA 18015-1982  USA 
Phone# 610 625-2702  Fax# 610 625-2775  
Web Site  www.vastex.com 
 

Authorized Representative in Europe: 
Certification Experts BV 
Nieuwstad 100 1381 CE Weesp,  
The Netherlands  
Tel : + 31 (0) 294 – 48 33 55  
Fax : + 31 (0) 294 – 41 46 87  

Serial Number: 

(Please log your machine's serial number and date of purchase for future reference.) 

Date:____

/

____

/

______ 

VTX 

Assembly and Operating Instructions  

Electrical Drawing #: 

Rev:______ 

 Contents 

Page# 



Safety Information 



General Information 



Package Contents 

4-5 



Component Identification 



Assembly 7-10 



Electrical Requirements/Controls 

11 



Operation 12 



Chain Drive Adjustment 

13 



10” Extension 

14 



 Warranty 

15 

D-100 and D-1000 Series Dryer

 

Doc. # 01-23-001E 

Year of Manufacture: 

20____ 

Summary of Contents for D-100

















Reviews: