Vax Impact 302 C86-ID-Be User Manual Download

Page: 5 / 16

Contents

Let’s talk safety

Getting to know your machine

Getting started

Using your machine

Taking care of your machine

Let’s talk technical

Accessories

What to do if it goes wrong

Getting in touch

Impact 302

Included with

your machine

Initial Setup for normal operation

Use the base accessories.

a. Shortest hose

b. Extension tube set to shortest practicable length.

Clean filters installed.

Dust receptacle empty.

All Bleeds must be closed.

Floor heads/tools set to Carpet Mode for carpet cleaning.

Mechanical Agitation turned ON for carpet cleaning.

Floor heads/tools set to Hard Floor Mode for hard floor cleaning.

Mechanical Agitation turned OFF for hard floor cleaning.

Telescopic extension tube

Combination floor head

Crevice tool

Dusting brush

Impact 302

Pet

TurboTool

4.2m Stretch hose

Tool connector

Pre-motor filter

Impact 302

Total Home

Post-motor filter

Accessory hose and handle

Summary of Contents for Impact 302 C86-ID-Be

















Search results

Summary of Contents for Impact 302 C86-ID-Be

Reviews:

Related manuals for Impact 302 C86-ID-Be

Brands by name

Popular brands

Vax Impact 302 C86-ID-Be, User Manual

Search results

Summary of Contents for Impact 302 C86-ID-Be

Reviews:

Related manuals for Impact 302 C86-ID-Be

Brands by name

Popular brands