background image

Twist the quick release  

cord hook to release the 

power cord.

Choose your desired 

carpet height or  

hardfloor setting.

Plug in your machine and 

push ON/OFF button to 

switch on.

Lie vacuum cleaner on its 

back exposing brushbar.

Align Hard floor adaptor 

with base of vacuum 

cleaner, push until its clicks 

into place.

Don’t over fill the dirt 

container to avoid clogging 

your filter.

Before you begin cleaning

•  Always switch off and unplug the vacuum cleaner before connecting or disconnecting the hose/attachments, or removing 

and emptying the dirt container.

•  The vacuum cleaner is equipped with a thermal cut-out. If for any reason the vacuum cleaner does overheat the thermostat 

will automatically turn the vacuum cleaner off. If this happens, switch the vacuum cleaner off and unplug from electrical 

socket. Remove and empty the dirt container also check the vacuum cleaner for blockages. Allow the vacuum cleaner to 

cool for approximately 1 hour (if you have cleaned the filters please wait 24 hours for the filters to fully dry before putting 

back into the vacuum).

•  Filters require cleaning at least every 3 months.
•  If the vacuum cleaner is blocked, switch off and unplug before removing the blockage.
•  When using the accessories always make sure the brushbar is switched to the off position.

IMPORTANT: 

When the vacuum cleaner is stood in the upright position or when using on stairs and the hose/tools,  

the brushbar height adjust dial must be set to hard floor.

Using your machine

How to use

Using the Hard Floor Adaptor

Apply the Hard floor adaptor for optimum results on hard floors.  

The Hard Floor Adaptor can be used on any floor setting.

TIP

To ensure the Hard floor adaptor 

is correctly fitted, the wheels 

should be towards the back of 

the floor tool when attached to 

vacuum cleaner.

Summary of Contents for U85-I3-Be

















Reviews: