background image

                                                                                                           

43 

When pressed, the emergency stop button locks in and therefore remains active. The current 

operating mode is stopped immediately, all movements are stopped; fault and error message 

appears; the machine cannot be restarted as the button locks in when pressed and thus remains 

active. After resolving the error, the emergency stop button must be pulled out as 

acknowledgement. 

6.2.3 Maintenance of robot movement mechanism 

Robot is a precision equipment, need time and maintenance, keep good lubrication condition, must 

strengthen the maintenance and maintenance, at any time, timing, clean up dirt, oil, ensure the 

robot to work under a good condition, this can avoid some faults occur frequently, reduce 

downtime, and can guarantee or to extend the service life of machine.

 

(一)

Daily Maintenance 

1.

 

Clean the solder and glue after working. 

2.

 

Must change or clean the tips frequently. 

3.

 

Don’t touch the track for avoiding rust. 

4.

 

Check if the parts are normal before work. 

(二)

Regular Maintenance 

You should maintain the machine about three months, if you always use it. The details are as 

follow: 

Take off the cover of X-axis, clean the screw and track, check the screw if loose or not, spread 

lubricant on the screw and track, move the X-axis for spread more lubricant. Then take on the 

cover. 

Take off the cover of Y-axis, clean the screw and track, check the screw if loose or not, spread 

lubricant on the screw and track, move the Y-axis for spread more lubricant. Check the screw of 

light sensor. Then take on the cover. 

Take off the cover of Z-axis, clean the screw and track, check the screw if loose or not, spread 

lubricant on the screw and track, move the Z-axis for spread more lubricant. Check the screw of 

light sensor. Then take on the cover. 

Belt: check if the belt is loosened. Adjust the belt if it loosened: firstly, disassemble the fixed 

screw. Secondly, pull the motor back. Then press the belt 10N stress at the mid of the belt, bend 

Summary of Contents for ET9484E















































Reviews: