background image

4

CAUTION:

(Caution statements advise against certain conditions and practices that may result

in damage to vehicles, appliances and/or The VECTOR

®

 Jump-starter)

IMPORTANT:

Although this unit is delivered in a partially charged state, you must fully charge it

with the supplied 110/120 Volt AC charger for a full 24 hours before using it for

the first time. You can not overcharge the unit using the AC charger method.

1) Use only the supplied cords/adapters for recharging this unit. Do not recharge

for more than 3-4 hours maximum using 12 Volt DC method. Recharge unit after

each use.

2) All On/Off switches should be in the OFF position when the unit is charging or

not in use. Make sure all switches are in the OFF position before connection to a

power source or load.

3) Never insert anything other than the supplied power/recharging cords or

recommended appliance power/recharging cords into the 12 Volt DC charging/

power socket on this unit. Do not use any accessory that is not recommended or

provided by the manufacturer.

4) Do not use this unit to operate appliances that draw more than 20 amps from

accessory socket.

5)  This system is designed to be used only on vehicles with 12 Volt DC battery

systems. Do not connect to a 6 Volt or 24 Volt battery system.

6) This system is not designed to be used as a replacement for a vehicular battery.

Do not attempt to operate a vehicle that does not have a battery installed.

7) Vehicles that have on-board computerized systems may be damaged if vehicle

battery is jump-started.  Before jump-starting, read the vehicle’s owners manual

to confirm that external-starting assistance is advised.

8) Excessive engine cranking can damage a vehicle’s starter motor. If the engine

fails to start after the recommended number of attempts, discontinue jump-start

procedures and look for other problems that may need to be corrected.

9) Although this unit contains a non-spillable battery, it is recommended that unit be

kept upright during storage, use and recharging. To avoid possible damage that

may shorten the unit’s working life, protect it from direct sunlight, direct heat

and/or moisture.

10) Check unit periodically for wear and tear. Replace worn or defective parts

immediately. Contact Vector Customer Service department toll-free 866-584-5504.

11) Do not attempt to jump-start a frozen battery.

12) Never submerge this unit in water.

13) DO NOT over-inflate tires.

Vec021APC manual 10/02

12/3/02, 10:56 AM

4

Summary of Contents for Start-It VEC021APC

















Reviews: