background image

9

FIRST AID:

• SKIN: If battery acid comes in contact with skin, rinse immediately with water, then

wash thoroughly with soap and water.  If redness, pain, or irritation occurs, seek

immediate medical attention

• EYES: If battery acid comes in contact with eyes, flush eyes immediately for

a minimum of 15 minutes and SEEK IMMEDIATE MEDICAL ATTENTION

3.

CHARGING/RECHARGING

For maximum battery life, we recommend the VECTOR

®

 JUMP-STARTER system is kept

fully charged at all time. If the battery is allowed to remain in a discharged state,

battery life will be shortened.

NOTE:

 Recharging battery after each use will prolong battery life; frequent discharges

between recharges will reduce battery life

IMPORTANT:

• MAKE SURE ALL SWITCHES ARE TURNED OFF DURING RECHARGING

• Charge unit for full 24 hours using AC method, prior to first use

• Recharge unit fully after each use

• Recharge unit every two months, when it has not been used

3.1

110/120 VOLT AC CHARGING

1. Simply plug the AC plug of the AC/DC adapter/charger into any standard 110/

120 volt AC wall outlet.

2. Plug the barrel connector attached to the AC/DC adapter into the small barrel

receptacle on the jump-starter that is marked recharge port.

3. Charge this device for at least 14-16 hours or until the green FULL indicator lights.

4. When charging is completed and the FULL light lights, remove the AC/DC charger

plug and store in a safe place.

NOTE:

The unit cannot be overcharged using the AC method. The VECTOR

®

 JUMP-STARTER

system also comes with a DC/DC charging adapter for recharging the unit from a 12

volt DC cigarette lighter or accessory socket in a vehicle or boat .

This recharging method will NOT recharge the unit as effectively as recharging from a

110/120 volt AC outlet. The 12 Volt DC recharging procedure is recommended only

when it is necessary, as continued use of the 12 Volt DC recharging procedure may

shorten the battery system’s life .

If unit is fully discharged, it is recommended that the vehicle being used for recharging

be left running while the unit is being charged via the 12 Volt DC method.

WARNING:

Do not recharge for more than 3-4 hours maximum using 12 Volt DC method

Vec021APC manual 10/02

12/3/02, 10:57 AM

9

Summary of Contents for Start-It VEC021APC

















Reviews: