background image

IQ Control Box Installation and Owner’s Manual

Determine the Motor Type

10

Determine the Motor Type

Warning! Disconnect, lock out, an tag power to the IQ Control Box at the panel

before starting these steps.

Determination of the Motor Type can be accomplished by measuring the resistance readings at the junction box in 
the STP and comparing to Table 1 or Table 2 below. Motor Type can also be determined by observing the flow 
paths in the top of the UMP (Figure 10). UMPs containing a Faradyne motor will also have an ‘FM’ designation 
printed on the UMP shell.

Figure 10.   Identifying UMP Models By Their End View

Table 1 and Table 2 show pump electrical service requirements for UMPs with end views A and B, respectively.

Table 1.  Electrical Service Information (for UMPs Containing a Franklin Motor with End View A)

Required power supply rating for 60 Hz, 1 phase pumps is 208 - 230 Vac. For 50 Hz, 1 phase pumps, required rating is 220 - 240 Vac.

UMP Model No.

HP

Hz

PH

Voltage 

Fluctuation 

Range

Max. 
Load 

Amps

Locked 

Rotor 

Amps

Winding Resistance (Ohms)

Capacitor Kit (µF)

Min.

Max.

Black-

Orange

Red-

Orange

Black-Red

AGUMP33S1, 

UMP33U1

1/3

60

1

200

250

4.0

13

7.7 - 9.4

17.4 - 21.2

25 - 30.7

144-224-5 (17.5)

E85

AGUMP75S1, 

UMP75U1

3/4

60

1

200

250

6.5

25

2.9 - 3.6

14.9 - 18.2

17.7 - 21.9

410164-001 (17.5)

E85

AGUMP150S1, 

UMP150U1

1-1/2

60

1

200

250

10.5

37

2.0 - 2.5

11.6 - 14.2

13.5 - 16.8

410164-002 (25)

E85

X3AGUMP150S1, 

X3UMP150U1

1/1/2

60

1

200

250

10.5

37

2.0 - 2.5

11.6 - 14.2

13.5 - 16.8

410164-002 (25)

Summary of Contents for 880-051-1







































Reviews: