background image

13

  

 Setup Web Server Security

Select the Security Mode

Select the Security Mode

On the first login to the FieldServer, the following screen will appear that allows the user to select which mode the 

FieldServer should use.

Figure 13.   Security Mode Selection Screen

Cookies are used for authentication.

To change the web server security mode after initial setup, go to “Update Firmware” on

page 25.

HTTPS WITH OWN TRUSTED TLS CERTIFICATE

This is the recommended selection and the most secure. Please contact your IT department to find out if you can 

obtain a TLS certificate from your company before proceeding with the Own Trusted TLS Certificate option.

Once this option is selected, the Certificate, Private Key and Private Key Passphrase fields will appear under the 

mode selection (see Figure 14).

Copy and paste the Certificate and Private Key text into their respective fields. If the Private Key is encrypted 

type in the associated Passphrase.

Click Save.

A “Redirecting” message will appear. After a short time, the FieldServer GUI will open.

NOTICE

NOTICE

Summary of Contents for ProtoNode FPC-N54
















































Reviews: