Veeder-Root ProtoNode FPC-N54 Startup Manual Download

Page: 46 / 47

Appendix A

Interface To BACnet & Modbus Tables

A-5

Table A-12. Smart_Sensor Veeder-Root Interface to BACnet, Modbus and SNMP

Table A-13. PLLD Veeder-Root Interface to BACnet, Modbus and SNMP

Point Name

BACnet

Object Type

BACnet

Object ID

Modbus

Register

SNMP OID

Smart Sensor X Setup Data Warninq

X001

10X01

1.3.6.1.4.1.6347.0.XX1.1.0

Smart Sensor X Communication Alarm

X002

10X02

1.3.6.1.4.1.6347.0.XX1.2.0

Smart Sensor X Fault Alarm

X003

10X03

1.3.6.1.4.1.6347.0.XX1.3.0

Smart Sensor X Fuel Warning

X004

10X04

1.3.6.1.4.1.6347.0.XX1.4.0

Smart Sensor X Fuel Alarm

X005

10X05

1.3.6.1.4.1.6347.0.XX1.5.0

Smart Sensor X Water Warning

X006

10X06

1.3.6.1.4.1.6347.0.XX1.6.0

Smart Sensor X Water Alarm

X007

10X07

1.3.6.1.4.1.6347.0.XX1.7.0

Smart Sensor X High Liquid Warning

X008

10X08

1.3.6.1.4.1.6347.0.XX1.8.0

Smart Sensor X High Liquid Alarm

X009

10X09

1.3.6.1.4.1.6347.0.XX1.9.0

Smart Sensor X Low Liquid Warning

X010

10X10

1.3.6.1.4.1.6347.0.XX1.10.0

Smart Sensor X Low Liquid Alarm

X011

10X11

1.3.6.1.4.1.6347.0.XX1.11.0

Smart Sensor X Temperature Warning

X012

10X12

1.3.6.1.4.1.6347.0.XX1.12.0

Smart Sensor X Relay Active

X013

10X13

1.3.6.1.4.1.6347.0.XX1.13.0

Smart Sensor X Install Alarm

X014

10X14

1.3.6.1.4.1.6347.0.XX1.14.0

Smart Sensor X Fault Warning

X015

10X15

1.3.6.1.4.1.6347.0.XX1.15.0

Smart Sensor X Vacuum Warning

X016

10X16

1.3.6.1.4.1.6347.0.XX1.16.0

Smart Sensor X No Vacuum Warning

X017

10X17

1.3.6.1.4.1.6347.0.XX1.17.0

Point Name

BACnet

Object Type

BACnet

Object ID

Modbus

Register

SNMP OID

PLLD X Setup Data Warninq

X001

10X01

1.3.6.1.4.1.6347.0.XX1.1.0

PLLD X Gross Test Fail Alarm

X002

10X02

1.3.6.1.4.1.6347.0.XX1.2.0

PLLD X Annual Test Fail Alarm

X003

10X03

1.3.6.1.4.1.6347.0.XX1.3.0

PLLD X Periodic Test Needed Warning

X004

10X04

1.3.6.1.4.1.6347.0.XX1.4.0

PLLD X Periodic Test Needed Alarm

X005

10X05

1.3.6.1.4.1.6347.0.XX1.5.0

PLLD X Sensor Open Alarm

X006

10X06

1.3.6.1.4.1.6347.0.XX1.6.0

PLLD X High Pressure Alarm

X007

10X07

1.3.6.1.4.1.6347.0.XX1.7.0

PLLD X Shutdown Alarm

X008

10X08

1.3.6.1.4.1.6347.0.XX1.8.0

PLLD X High Pressure Warning

X009

10X09

1.3.6.1.4.1.6347.0.XX1.9.0

PLLD X Continuous Handle On Warning

X010

10X10

1.3.6.1.4.1.6347.0.XX1.10.0

PLLD X Periodic Test Fail Alarm

X011

10X11

1.3.6.1.4.1.6347.0.XX1.11.0

PLLD X Annual Test Needed Warning

X012

10X12

1.3.6.1.4.1.6347.0.XX1.12.0

PLLD X Annual Test Needed Alarm

X013

10X13

1.3.6.1.4.1.6347.0.XX1.13.0

PLLD X Low Pressure Alarm

X014

10X14

1.3.6.1.4.1.6347.0.XX1.14.0

PLLD X Sensor Short Alarm

X015

10X15

1.3.6.1.4.1.6347.0.XX1.15.0

PLLD X Continuous Handle On Alarm

X016

10X16

1.3.6.1.4.1.6347.0.XX1.16.0

PLLD X Fuel Out Alarm

X017

10X17

1.3.6.1.4.1.6347.0.XX1.17.0

PLLD X Line Equipment Alarm

X018

10X18

1.3.6.1.4.1.6347.0.XX1.18.0

PLLD X Gross Test Needed Alarm

X019

10X19

1.3.6.1.4.1.6347.0.XX1.19.0

Summary of Contents for ProtoNode FPC-N54
















































Search results

Summary of Contents for ProtoNode FPC-N54

Reviews:

Related manuals for ProtoNode FPC-N54

Brands by name

Popular brands

Veeder-Root ProtoNode FPC-N54, Startup Manual

Search results

Summary of Contents for ProtoNode FPC-N54

Reviews:

Related manuals for ProtoNode FPC-N54

Brands by name

Popular brands