Veeder-Root V454502 Technical Manual Download

Page: 12 / 12

The order codes for the Veeder-Root 454502 Dual Preset Counter are shown below:

Dual Preset Counter (USA)

V45450-2

Dual Preset Counter (UK/Europe)

V45450E2

Dual Preset Counter (USA) - Low Voltage AC/DC supply

V45450-22

Dual Preset Counter (UK/Europe) - Low Voltage AC/DC supply

V45450E22

In the UK:

Veeder-Root Division

West Instruments Limited
The Hyde
Brighton
E. Sussex BN2 4JU

Tel. +44 (0) 1273 606271
Fax: +44 (0) 1273 609990

In France:

Veeder-Root SARL

8 Place de la Loire
94583 Rungis Cedex

Tel. 33-146870981
Fax: 33-146868004

In Germany:

Veeder-Root GmbH

Morikestrasse 30
73761 Neuhausen ADF

Tel. 49-71589003-0
Fax: 49-71589003-32

In Brazil:

Veeder-Root do
Brasil

Rua Ado Benatti No-92
Caixa Postal, 8343
CEP 05037-010
São Paulo

Tel. 55-118612155
Fax: 55-118611982

1675 N. Delany Road
Gurnee, IL
60031-1282

Tel. 708.662.2666

This instrument is warranted to be free from defects in workmanship and material for a period

of three years from the date of despatch. In the unlikely event of a fault, call the appropriate

number below for a Return Material Authorisation (RMA) number.
The obligation of the Company under this warranty is limited to the repair or replacement of

this instrument. Should the cause of the fault be due to misuse or abuse of the instrument or the

warranty period has expired, the customer shall be informed before any repair work is started.

Summary of Contents for V454502













Search results

Summary of Contents for V454502

Reviews:

Related manuals for V454502

Brands by name

Popular brands

Veeder-Root V454502, Technical Manual

Search results

Summary of Contents for V454502

Reviews:

Related manuals for V454502

Brands by name

Popular brands