background image

10

3 Product description

VEGACAL 69 • Two-wire 4 … 20 mA/HART

31178-EN-200929

• 

with the suitable VEGA DTM in conjunction with an adjustment 

software according to the FDT/DTM standard, e.g. PACTware and 

PC

• 

With manufacturer-specific adjustment programs AMS™ or PDM

• 

With a HART handheld

3.4  Packaging, transport and storage

Your instrument was protected by packaging during transport. Its 

capacity to handle normal loads during transport is assured by a test 

based on ISO 4180.
The packaging of standard instruments consists of environment-

friendly, recyclable cardboard. For special versions, PE foam or PE 

foil is also used. Dispose of the packaging material via specialised 

recycling companies.

Transport must be carried out in due consideration of the notes on the 

transport packaging. Nonobservance of these instructions can cause 

damage to the device.

The delivery must be checked for completeness and possible transit 

damage immediately at receipt. Ascertained transit damage or con-

cealed defects must be appropriately dealt with.

Up to the time of installation, the packages must be left closed and 

stored according to the orientation and storage markings on the 

outside.
Unless otherwise indicated, the packages must be stored only under 

the following conditions:

• 

Not in the open

• 

Dry and dust free

• 

Not exposed to corrosive media

• 

Protected against solar radiation

• 

Avoiding mechanical shock and vibration

• 

Storage and transport temperature see chapter " 

Supplement - 

Technical data - Ambient conditions

• 

Relative humidity 20 … 85 %

With instrument weights of more than 18 kg (39.68 lbs) suitable and 

approved equipment must be used for lifting and carrying.

3.5 Accessories

The instructions for the listed accessories can be found in the down-

load area on our homepage.

The display and adjustment module is used for measured value indi-

cation, adjustment and diagnosis.
The integrated Bluetooth module (optional) enables wireless adjust-

ment via standard adjustment devices.

Packaging

Transport

Transport inspection

Storage

Storage and transport 

temperature

Lifting and carrying

PLICSCOM

Summary of Contents for VEGACAL 69





























































Reviews: