background image

4

13

I/O = On and Off 

Speed up

Seat tilt

Joystick

Electric seat lift

Speed down

Alarm horn

1.0. operaTion

This powerchair is a class A (EN 12184) electric wheelchair. The first attempts to 
operate the chair should be made in an area with plenty of floor space.
Choose a low operating speed (press the “down button” a few times) until you have 
become accustomed to the chair.

JoysTiCK

1.1. before operaTion

Before starting the powerchair, you should check the following:

• The footrest is in place and both feet are placed properly on the footplate.
• The electric lift (seat lift) is in the lowest position.
• The electric tilt (seat tilt) is in  neutral position.
• Both motors are connected. The arrow points to:.
• The powerchair is turned on by pressing the I/O button.

enTering and exiTing

Always turn off the power before entering or exiting the chair (the I/0 button).

fooTresTs

Any footrests should be swivelled to the side or the footplate should be folded up 
before exiting the chair.

Warning! Do not stand on the footplate or footrests – the chair can tip and you may 
loose your balance.

parT

MainTenanCe 
Carried ouT by

MainTenanCe

inTerVal

WHEELS

User

Check that the tyres are not worn and that 
stones or other objects are not sitting in 
the tread. 
If the wheels are pneumatic, check the air 
pressure, which must be between 2.20-3.5 
Kilo Pascal. 
The wheel can be inflated with either a car 
pump or at a service station.

Once a 
month, 
depending 
on use

CHANGING 
WHEELS

VELA

Contact VELA

CONTrOL BOx

User

The control box and the rubber seal 
around the joystick must always be kept 
clean. Once a week, you should check that 
the joystick returns to its original position 
and that the rubber seal has not been 
damaged. If this is not the case, contact 
VELA.

Once a 
week

TESTING 
CONTrOL BOx 
fUNCTIONS

User

1. Check the on-off switch.
2. Check the horn.
3. Check the speed – try accelerating and 
decelerating.
4. Check the seat lift – raise and lower the 
seat to its full extent.
5. Check the seat tilt – tilt the seat all the 
way backwards and all the way forwards.
If any of the functions do not work or if 
anything feels different to normal, contact 
VELA. 

Once a 
month

BATTErIES

VELA

Batteries must be replaced by VELA.
If the batteries are leaking, avoid touching 
them as the contents are corrosive.

In the event 
of flat or 
defective 
batteries

ACCESSOrIES

User

All accessories such as footrests, armrests 
and body supports must be adjusted using 
the tools supplied.

Once a 
month

Summary of Contents for Blues 100

















Reviews: