VELGE Fannaraki, Installation, Operating And Maintenance Instructions

www.velgehome.com

if set at the 2

nd

, 3

rd

 and 4th speed.

T4 is selected with the key top speed of aspiration for 10 minutes (flashing 

key), after which the fan will automatically switch to 3

rd

 speed.

Change of air

By pressing the T5 control, you activate the change of air, which keeps on 

functioning for 24 hours. The extractor turns on at the first speed for 5 

minutes, then it turns off automatically. This timed cycle repeats every 25 

minutes. During extraction the light of the command blinks, otherwise it 

is fixed. This function is easy to deactivate by pressing the desired speed.

Adjustable and delayed self switching off

While the hood is working, keep the TL command pressed until all leds 

start blinking.

By pressing one of the commands (T1, T2, T3) you can program the 

delayed self switching off, as follows:

T1

 corresponds to 5 minutes

T2

 corresponds to 10 minutes

T3

 corresponds to 15 minutes

While the self switching off is in function, it is possible to modify the 

speed previously set.

If the same command corresponds both to the time of delayed self 

switching off and to the speed, then the led blinks; if the commands are 

different, the speed led has a fixed light.

Filters maintenance reminder

Aluminium anti-grease filters

Once the hood is switched off, after 30 hour functioning, all the leds of the 

speed buttons switch on with a fixed light for 30 seconds to remind that 

aluminium anti-grease filter need cleaning.To set the timer to zero keep 

the button T1 pressed with the aspirator switched off, otherwise the timer 

will remain set on 30 hour functioning and the reminder will occur again 

when the hood is switched off again.

Charcoal filter (for filtering hoods)

Once the hood is switched off, after 120 hour functioning, all leds blink 

for 30 seconds to remind that the charcoal filter need cleaning. To set 

ensures the disconnection, with an opening distance of the contacts 

allowing a complete disconnection on the conditions of the overvoltage 

III category, according to installation regulations. The ground connection 

(yellow-green wire) must not be interrupted. Refer to the plate inside the 

hood for the mains voltage and frequency ratings.

EMPLOYMENT

This cooker hood can be employed as exhausting or filtering.

Exhausting 

(external evacuation). Kitchen smokes are driven outside 

through a flue joined to the exhaust pipe flue connector.

This pipe must not under any circumstances be connected to cooker, 

boiler or burner exhaust pipes, etc.

Filtering 

(inside recycling). Smokes pass through the activated charcoal 

filter (Picture 3 - G) to be cleaned and recycled in the kitchen environment 

by means of holes from which the purified air will come out. These holes 

have to be free and communicating with the kitchen environment. In this 

case you should not install the exhaust pipe without curve.

OPERATION

The hood is supplied with a multispeed motor. The hood should 

be run at low speed under normal conditions and at higher speeds 

only when there is a heavy buildup of fumes or odours. Ideally, the 

hood should be switched on as soon as cooking is started and then 

kept on until all odours have been eliminated.

The controls consist of these commands. Press 

TL

 to turn on the 

light, press 

T1

 to swich on the hood at first speed and to switch off 

the aspirator, press 

T2-T3-T4

 to select functioning speeds.

By pressing of the command T1 the motor starts running at the 1st 

speed. The commands T2-T3-T4 switch the motor on respectively 

at the 2

nd

, 3

rd

 and 4

th

 speed, press 

T5

 to air exchange function.

In order to switch the motor off press T1 once if set at the 1st speed, twice