background image

FIG.V

1.The bicycle computer is water-resistant and can 

be used in light rain showers.

2.The battery for the sensor and computer can be

used for 1 year if it is used for 2 hours each day.

3.The maximum space between bicycle computer

and sensor should be 90cm, a nd the angle s hould

not be over 30°. The distance between magnet

and sensor should be no more than 5 mm.

4.Avoid draining the battery when you are not using the

computer, it is recommended to keep the

magnet away from the sensor.

5.Please do not use the product near a microwave

oven, TV, computer, mobile phone or any other

wireless device. The electromagnetic interference

from some devices can cause an inaccurate read out.

16

17

instantaneous speed is 10.0km/h. In that case, your 

current  speed  is  faster  10.0km/h  than  the  average 

speed.  If  the  instantaneous  speed  is  lower  than 

average speed, RES will show minus. 

6.Press MODE again and switch to the display as 

FIG. V

i.MXS  shows  the  fastest  speed 

during riding is 30.5km/h.

ii.ODO  shows  the  total  distance

from replacing the battery.

iii.The ODO value can not be reset to 

zero by pressing SET button, instead 

hold MODE andSET buttons at the 

same time for 2 seconds. 

 N O T E

Note:

  After  cycling  for  more  tha n  9H 59M59S 

(the  ma x  time  for memory ),  the  a vera ge 

s peed  will  dis pla y  incorrectly.  P lea s e 

clea r both exercis e  time  a nd dis ta nce  to 

z ero  to  get  a  correct  va lue  of  the 

a vera ge s peed.

Summary of Contents for VS 213











Reviews: