background image

Gas connection 

The cooker must be connected to the gas supply with upstream connection of an 
isolation valve in accordance with the respectively valid re

g

ulations. We 

recommend that the isolation valve be fitted prior to the cooker to enable isolation 
of the cooker from the gas supply. The valve must be easily accessable at all times. 
To find out the factory set gps type, see 

the 

label at 

the 

rear of 

the 

cooker

.

 

The gas connection is via 1/2" compression. Connect the cooker to the gas supply 
and check for gas soundness. 

NEVER

 use a naked flame to check for gas leaks. 

 

Gas inlet (mm)- 

Nat gas  

 

 

         Gas inlet (mm)- LPG 

From RH rear side: 35

 

mm    

From RH rear side: 35mm

 

Up from floor: 590 mm 

 

 

 

 

Up from floor: 675 mm

 

 
    

 

 
 
 
 
 
 
 
 
Gas inlet with different leg heights – mm 

Min  NG: 560 

LP: 645 

Ref  NG: 590 

LP: 675 

Max  NG: 595 

LP: 680 

 

Energy consumption 

 

 

 

Burners Gas 

type 

Pressure (kPa) 

Injector

 (mm) Mj/hr 

Watts

Small Natural 1.0 

0.90 4.00 

 

 

U-LPG 2.75 

0.54 3.75 

 

Medium Natural  1.0 

1.18  7.12 

 

 

U-LPG 2.75 

0.70 6.20 

 

large Natural 1.0  1.55 

12.5 

 

 

U-LPG 2.75 

0.92 11.25  

Wok Natural 

1.0  1.65 

13.1 

 

 

U-LPG 2.75 

0.98 13.0 

 

Oven

 

Natural 1.0 

1.80 16.5 

 

 

U-LPG 2.75 

1.10 16.6 

 

Grill    

 

  2350 

W

 
 
 

Summary of Contents for VEF91GG






















Reviews: