background image

Test the operation of the cooker before leaving 

Note: These burners have no aeration adjustment

.

 

Check correct operation of the ignitions system and operation of burners individually and in 
combination. Burner flames should be clear blue, with no yellow tipping. If the burners 
show any abnormality check that the burners are correctly located. If satisfactory 
performance can not be obtained, contact the local gas utility.  

 

Important 

Before leaving instruct the owner in the use of the cooker

.

 

I

t should be expressly noted that 

we cannot accept any liability for direct or indirect damage caused by wrong connection or 
improper installation. When being repaired, the appliance must always be disconnected 
from the mains supply; if required, notify our customer service

.

 

 

 
 

Support legs 

The cookers 

a

re supplied with four transit supports.(One for each corner). 

4 support legs 

a

re supplied separately and are fitted on location to the four corners 

of the lower support frame. Each support leg is pushed over the relevant transit 
support until flush with the support frame. 

Each leg is adjusted by screwing the lower section in or out as required for fitting to a 
900mm bench height. For lower bench tops a

djust the height as 

required.The adjustment 

range for the leg is 150-185mm. With the legs adjusted to a height of 180mm the hob is 
located 10mm above the horizontal combustable surface, ref. AS5601

.

 

 

 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 

 

Summary of Contents for VEF91GG






















Reviews: