background image

About this Document  

 

Kinetic MVHR Installation & Commissioning 

3

 

 

Contents 

Important Safety Information .......................................................... 2

 

Installation Guidance ...................................................................... 2

 

Product Description 

 

Kinetic Plus E ................................................................................. 4

 

Technical Data 

5

 

KINETIC Plus E Performance graph .............................................. 6

 

Installation ...................................................................................... 7

 

Overview ........................................................................................ 7

 

Before Installation of the Unit ......................................................... 7

 

Unit Installation ............................................................................... 7

 

Electrical Installation..................................................................... 16

 

Powering Up the Unit ................................................................... 18

 

Commissioning

 

Overview ...................................................................................... 19

 

Commissioning Control ................................................................ 20

 

Maintenance 

 

Filter Maintenance ........................................................................ 22

 

12 Monthly Maintenance .............................................................. 22

 

Spares 23 

 

Product Fiche 

24

 

   

 

UK Building Regulations (Part F) 
Declaration of Conformance 

Kinetic Plus E conform to the 2010 Building Regulations 
(Part F - Means of Ventilation) installed performance of a 
ducted mechanical extract fan when installed in 
accordance with the instructions in this document and the 
domestic ventilation compliance guide. 

 

Note:  

Read in conjunction with the User Instructions manual 
445350.

Summary of Contents for Kinetic Plus E


























Reviews: