background image

Page 2 

                                                        

Specifications are subject to change without notice.      

Installation Instructions

 

Distributed by Simx Limited                                                                                                     

            

sales@simx.co.nz | www.manrose.co.nz

MultiVent Continuous Extract Ventilation

MULTIVENT CONTINUOUS EXTRACT VENTILATION SYSTEM INSTALLATION

AND ELECTRICAL CONNECTION MUST BE CARRIED OUT BY A REGISTERED ELECTRICIAN

BEFORE INSTALLING THE MULTIVENT CONTINUOUS EXTRACT VENTILATION SYSTEM, MAKE SURE YOU 

HAVE TURNED OFF THE MAIN ELECTRICITY SUPPLY. DO NOT TURN IT BACK ON UNTIL THE MULTIVENT 

CONTINUOUS EXTRACT VENTILATION SYSTEM IS FULLY

INSTALLED AND READY TO USE.

ALL ELECTRICAL WORK MUST BE CARRIED OUT BY A REGISTERED ELECTRICIAN IN ACCORDANCE

WITH THE LATEST WIRING RULES AS/NZS3000.

CAUTION

•  Do not install this product where excessive oil or a grease laden atmosphere is or may be, present

•  Do not install this product where corrosive or flammable gases, liquids or vapours are, or may be, present

•  Do not install this product where it may be subject to direct water spray from hoses

•  Do not install this product where access to, or removal, of the unit may be obstructed

•  Before use, please check that the supply voltage and that of the appliance are the same (see product rating label).
•  All wiring and wiring connections must comply with all current national wiring rules and regulations including AS/NZS3000:2017, 

 

 

or latest edition thereof.

•  Any changes or modifications made or attempted to this product, without the prior written approval of the manufacturer, 

 

 

 

will void any and all stated warranties.

•  This MultiVent continuous extract ventilation system is not intended for use by persons (including children) with reduced physical, sensory or  
 

mental capabilities, or lack of experience and knowledge, unless they are capable of, and have been given supervision or instruction concerning  

 

use of the appliance by a person responsible for their safety.

•  Children should be supervised to ensure that they do not play with the MultiVent continuous extract ventilation system.
•  In case of damage to the supply cord, switch off the device and do not tamper with it. Damaged supply cords must only be repaired or  

 

 

replaced exclusively by the manufacturer or by an appointed representative. Failure to comply with the above may endanger the safety of    

 

people and cause possible damage to the whole system.

•  The unit must not be connected directly to a tumble drier.
•  Precautions must be taken to avoid the back-flow of gases into the room from the open flue of gas or other fuel-burning appliances.
•  The exhaust grille should be located at least 600mm away from any flue outlet.

IMPORTANT

•  This MultiVent continuous extract ventilation system is hot when in use. To avoid burns, do not let bare skin touch hot surfaces.   

 

 

Keep combustible materials away from the unit and keep them away from the sides and rear.

•  Do not use near or in the immediate vicinity of a bath or swimming pool or any wet areas.
•  When installing fan through an external wall, an external wall grille must be fitted at all times.
•  This appliance incorporates an earth connection for functional purposes only.
•  To protect against electric shock, do not immerse cord or plug in water or any other liquids.
•  Do not insert or allow foreign objects to enter any ventilation openings, as this may cause an electric shock, fire or damage to the fan.
•  Do not put fingers or foreign objects into the grille while in operation.
•  Any changes or modifications made or attempted to this product, without the prior written approval of the manufacturer, will void any 

 

 

and all stated warranties.

•  To prevent overheating of this fan, keep the air inlets and outlets clean and free of anything that may cause blockage.   

 

 

 

Check all inlets and outlets from time to time to ensure it is clear of any dirt or dust accumulation. DO NOT COVER.

•  Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
•  This product contains recyclable materials. Do not dispose of this product as unsorted council waste. Please contact your local council for   
 

the nearest collection point. 

Summary of Contents for MultiVent FAN7453













Reviews: