VentAHood DAH18 Installation Instructions Manual Download

Page: 15 / 15

Page

THE INFORMATION IN THIS DOCUMENT IS SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE.

PARTS FOR VENT-A-HOOD PRODUCTS

MOTORS

PART NO.

DESCRIPTION

PRICE

P1301-1

SINGLE SPEED WHITE MOTOR (CW)

P1301-2

TWO SPEED WHITE MOTOR (CW)

P1302-1

BLACK MOTOR (CCW)

P1315

K SERIES MOTOR

P1900

ADAPTER (AMP PLUG/TWO PRONG PLUG)

BLOWER WHEELS

PART NO.

DESCRIPTION

PRICE

P1305

WHITE BLOWER WHEEL (CW)

P1306

BLACK BLOWER WHEEL (CCW)

P1307

K SERIES BLOWER WHEEL

BLOWER HOUSINGS

PART NO.

DESCRIPTION

PRICE

SPECIFY HOOD COLOR

P1029

B100/T200 BLOWER HSG w/DAMPER

P1029E

B100/T200 EZ CLEAN HSG w/DAMPER

P1028

B200/T400 BLOWER HSG w/DAMPERS

P1028E

B200/T400 EZ CLEAN HSG w/DAMPERS

P1030

T200 REVERSE BLOWER HSG w/DAMPER

P1030E

T200 REVERSE EZ CLEAN HSG w/DAMPER

P1021

K SERIES BLOWER COVER (PAN)

BLOWER SHIELDS

PART NO.

DESCRIPTION

PRICE

P1025

B100/T200 SHIELD (ENAMEL)

P1025E

B100/T200 EZ CLEAN SHIELD (ENAMEL)

P1027

B100/T200 SHIELD (STAINLESS)

P1027E

B100/T200 EZ CLEAN SHIELD (STAINLESS)

P1024

B200/T400 SHIELD (ENAMEL)

P1024E

B200/T400 EZ CLEAN SHIELD (ENAMEL)

P1026

B200/T400 SHIELD (STAINLESS)

P1026E

B200/T400 EZ CLEAN SHIELD (STAINLESS)

P1610P

NICKEL SHIELD SCREW

SWITCHES AND CONTROLS

PART NO.

DESCRIPTION

PRICE

P1430

SWITCH FOR SINGLE SPEED WHITE MOTOR

P1431

SWITCH FOR SINGLE SPEED BLACK MOTOR

P1432

SWITCH FOR FLUORESCENT LIGHT

P1433

SWITCH FOR TWO SPEED WHITE MOTOR

P1434

SWITCH FOR HALOGEN LIGHTS

P1409

MOMENTARY SWITCH (TILT/TLH HOODS)

P1418

DIMMER SWITCH (CAN LIGHTS)

P1419

ROTARY SWITCH (HEAT LIGHTS)

P1422

KNOB FOR ROTARY SWITCH (SET SCREW)

P1425

REMOTE BLOWER SPEED CONTROL (HOOD)

M LINE COMPONENTS

PART NO.

DESCRIPTION

PRICE

P1440

M LINE BLOWER SWITCH

P1445

M LINE BLOWER SWITCH KNOB

P1450

M LINE LIGHT SWITCH

P1455

M LINE LIGHT SWITCH KNOB

P1456

M600 WIRING HARNESS

P1457

M1200 WIRING HARNESS

LIGHT BULBS

PART NO.

DESCRIPTION

PRICE

P1110

GU10 HALOGEN BULB, 50 WATT

P1120

F15/T8 FLUORESCENT BULB, 15 WATT

P1130

PAR20 HALOGEN BULB, 50 WATT

LIGHT FIXTURE COMPONENTS

PART NO.

DESCRIPTION

PRICE

P1101

SP2 BALLAST (NEWER HOODS)

P1103

LEFT LAMPHOLDER

P1104

RIGHT LAMPHOLDER

P1105

FS-2 STARTER

P1106

STARTER SOCKET

P1122

HEAT LAMP SOCKET

P1123

PAR20 HALOGEN LAMP SOCKET

P1124

GU10 HALOGEN LAMP SOCKET

COMPLETE FLUORESCENT LIGHT FIXTURES

PART NO.

DESCRIPTION

PRICE

INCLUDES 18” FLUORESCENT BULB (P1120)
SPECIFY MODEL, COLOR, AND SIZE OF HOOD
NOT AVAILABLE IN STAINLESS STEEL, USE GUNSMOKE

P1016

3” LIGHT BOX (WALL MOUNT & ISLAND)

P1018

2” LIGHT BOX (UNDER CABINET)

PxxxB

FIXTURE WITH BACK, ADD

P1127

FLUORESCENT LIGHT DIFFUSER

REPLACEMENT FILTERS

PART NO.

DESCRIPTION

PRICE

P1501

CV FILTER (11-1/2” DIA. X 4-1/2”T)

P1502A

MESH (16” x 20” x 2”)

P1502B

MESH (10” x 20” x 2”)

P1506

SS BAFFLE (16” x 20” x 1-1/2”)

P1506A

SS BAFFLE (10” x 20” x 1-1/2”)

P1530

M LINE BAFFLE FILTER

BACK DRAFT DAMPERS

PART NO.

DESCRIPTION

PRICE

P1031

NYLON POLYMER DAMPER

P1040

B100/T200 METAL DAMPER

P1041

B200 METAL DAMPER

P1042

K SERIES DAMPER

REMOTE BLOWER COMPONENTS

PART NO.

DESCRIPTION

PRICE

P1425

REMOTE BLOWER SPEED CONTROL (HOOD)

P1510

RM1000 BLOWER WHEEL

P1515

RM1000 MOTOR

P1520

RM1500 BLOWER WHEEL

P1525

RM1500 MOTOR

OTHER MISCELLANEOUS ITEMS

PART NO.

DESCRIPTION

PRICE

P1039

FLAP STAY FOR TILT/TLH HOODS

AW101

T-HANDLE, 1/8” ALLEN WRENCH

AW102

STANDARD, 1/8” ALLEN WRENCH

P1424

SENSASOURCE THERMOSTAT ASSY

SS KIT

STAINLESS STEEL SCRATCH REPAIR KIT

SS64

STAINLESS STEEL MAGIC (CAN)

CP101

RED BEAR® COPPER POLISH

P1316

3-1/4” x 10” COLLAR FOR K SERIES

P1317

BACK PLATE FOR K SERIES

email: customer_service@ventahood.com

website: www.ventahood.com

4/16/2012 Rev. 1

Summary of Contents for DAH18
















Search results

Summary of Contents for DAH18

Reviews:

Related manuals for DAH18

Brands by name

Popular brands

VentAHood DAH18, Installation Instructions Manual

Search results

Summary of Contents for DAH18

Reviews:

Related manuals for DAH18

Brands by name

Popular brands