background image

JCH/B1 Series  

Equipped with LED lighting. Not available with heat lamps. Shown with optional duct 

cover (sold separately). Optional duct covers available in standard and custom sizes.

DESIGNER SERIES WALL MOUNT RANGE HOOD

UL

C

US

R

OPTIONAL 

DUCT 

COVER

Centerline

Of Hood

Wall Side

Electrical (2)

10" Outlet

Centered On

Hood Top

12 7⁄8”

9 1⁄8”

1 ¾”

Wall Side

7"

Electrical (2)

Centerline

Of Hood

12" Outlet

Centered On

Top Of Hood

1 ¾”

16 ½”

5 ½”

1 ¾”

Electrical

1 ¾”

Centerline

of Hood

8” Outlet

Vent

Holes

5 ¼”

5 ½”

Wall Side

*Recommended mounting 

height is for optimum 

performance.

Recommended

Mounting Height

Connection Diagrams (36" - 48" Widths)

Connection Diagram (48" - 60" Widths)

Connection Diagram (54" - 66" Widths)

B100 Single Blower

(Top View)

(Front View)

B200 Dual Blower

(Top View)

(Front View)

900 CFM B200 Dual & B100 Single Blower

(Top View)

VP562 Standard Transition

Installed (Front View)

1200 CFM Double B200 Dual Blowers

(Top View)

VP563 Standard Transition

Installed (Front View)

10” Round

10” Round

8” Round

17 ½”

2”

8” Round

6” Round

12” Round

12” Round

16 ½”

8” Round

8” Round

8” Round

3”

VP562 Standard Transition

Included

VP563 Standard Transition

Included

36"

30"

































6” Outlet

Vent

Hole

3 ¼”

Electrical

Centerline

of Hood

Wall Side

1 ¾”

1 3⁄8”

5 ¼”

Electrical/Mechanical Specifications For Blower Units

Model

Volts

Amps

Hz

RPM

CFM

SP@0.0"

Equivalent CFM

CFM

SP@0.1"

CFM

SP@0.2"

CFM

SP@0.3"

Minimum Round

Duct Size

Sones

#

B100 Single

115

2.5

60

1550

300

450

273

245

225

6" (28 in.

2

)

5.4

B200 Dual

115

4.0

60

1550

600

900

531

480

430

8" (50 in.

2

)

6.5

B200 Dual & B100 Single

115

6.0

60

1550

900

1350

804

725

655

VP562: 10" (79 in.

2

)

6.3

Two B200 Duals

115

7.5

60

1550

1200

1800

1062

960

860

VP563: 12" (113 in.

2

)

6.6

  Hoods are available with LED lights (2 lights: 30" - 41", 3 lights: 42" - 53", 4 lights: 54" - 66").

•  Because the Magic Lung

®

 blower uses centrifugal filtration rather than conventional baffle or mesh filters, the Magic Lung

®

 blower can handle cooking equipment with higher cubic feet per minute (CFM) requirements and can deliver equivalent CFM much more 

efficiently than other than other filtration systems. When comparing the Magic Lung

®

 with other blower units made by other manufacturers, use the “Equivalent CFM”.

#  Ratings in accordance with the Standard Test Code by the Energy Systems Laboratory of the Texas Engineering Experiment Station.

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE 

Rev. 0715A

Summary of Contents for JCH/B1 Series
















Reviews: