background image

2.2.b .   Functions of the programming module: (1)

Adjustment using the clock:
Navigate with keys 19 or 20 to pictogram 1 showing a clock. 
Select with key 18 The pictogram will flash Validate with key 18

Select with key 18. The pictogram will flash. Validate with key 18.
Adjust the desired hour using keys 19 and 20. 
Validate with key 18. Pictogram 3 (day) will flash. Validate with key 18.
Adjust the day, knowing that the succession can be destined from 1 to 7 on any day.

Airflow adjustment (From 90 m

3

/h to 275 m

3

/h): (5)

Minimum airflow:
Navigate with keys 19 or 20 to pictogram 4 showing flows. 
Select with key 18. The pictogram of the first fan will flash. Validate with key 18.
Adjust the minimum desired flow using keys 19 and 20 in 5 m

3

/h steps, according to the 

configuration of your house (in compliance with the table). 

Maximum airflow:
Validate with key 18 The pictogram with two fans will flash Validate with key 18

Validate with key  18. The pictogram with two fans will flash. Validate with key 18.
Adjust the maximum desired flow using keys 19 and 20 in 5 m

3

/h steps, according to the 

configuration of your house (following the table show below).

Validate with key 18.

Programming module options (2):
There are two pre-established programming modes and one user-chosen mode. The 
modes are to past to the minimum airflow at the maximum airFlow.
To access the desired mode:
Navigate with keys 19 or 20 to Auto 1, Auto 2  or Manu pictogram . (Automatic 1, Automatic 
2 or Manual)
Select with key 18. Select On/Off using keys 19 or 20. Validate the chosen programming 
with key 18.

- Auto 1:
Working week with two meals per day, three in the weekend, but starting breakfast two 
hours later.

Day

Start

Finish

Start

Finish

Start

Finish

Monday

6:30

7:30

19:30

20:30

T1

T2

T3

Monday

6:30

7:30

-

-

19:30

20:30

Tuesday

6:30

7:30

-

-

19:30

20:30

Wednesday

6:30

7:30

-

-

19:30

20:30

Thursday

6:30

7:30

-

-

19:30

20:30

Friday

6:30

7:30

-

-

19:30

20:30

Saturday

8:30

9:30

12:00

13:00

19:30

20:30

Sunday

8:30

9:30

12:00

13:00

19:30

20:30

Summary of Contents for IDEO - 275 Ecowatt

















Reviews: