background image

GENERAL OPERATION

Operation - 17

Transport of Mower

Transport the mower deck with the power unit front 

hitch and mower fully raised to reduce wear of the 

equipment. Travel slowly when transporting over 

undulating and rough surfaces to maintain control of 

power unit and to reduce the shock to the power unit 

and mower deck. Always disengage the power unit 

PTO before transporting the mower.

Cutting Height Adjustment

1. 

 

Always shut off the engine, remove the ignition 

key, and set the parking brake before checking 

mower deck or blade condition, or attempting 

any repair or adjustment.

Lift the height adjustment handle upward and 

hook the lock pin into the notch (A) on the height 

setting control bracket.

2. 

A

B

Pull the handle outward to release the catch 

from the height adjust selector plate (B) .

3.  Rotate the height adjustment handle up or down 

until the desired setting is reached.

4.  When the desired cutting height is reached, 

release the height adjustment tab into the proper 

slot on the selector plate.

5.  Lift the height adjustment handle free of the 

height setting control bracket and rotate down to 

lay on the deck.

Summary of Contents for Ventrac LM440




































Reviews: