l
Automatic Analysis. Each of the samples is identified by placing a numbered grid
over each individual sample. The operator then has the option to activate the auto-
matic analysis mode. When activated the system will identify the sample profile and
its position within its own grid boundary. The program will then systematically ana-
lyse the deformation of each of the sequential images and identify each of the
deformation points. When the program has finished analysing the images the critical
deformation temperatures are automatically displayed in the results form along
with the individual sample identification. Graphical data of the melting profiles are
also recorded. The results table can then be saved and printed out in report form.
Note
: Only 8 samples can be automatically analysed at any one time.
l
Manual Analysis. To aid analysis each of the samples is identified by placing a
numbered grid over it. Analyses is aided by the use of a results form, which enables
the critical deformation temperatures to be entered manually along with individual
sample identification. The results form can then be saved and printed out in report
form.
In both cases the software automatically starts and stops the furnace controller, the
start temperature and interval between images is adjustable to suit your requirements.
See section 4.7.2.2.
The software is designed primarily to be used with a mouse, however most operations
are selectable from the keyboard if necessary and are as follows:
l
Commands on the text menu bar at the top left of the screen are activated using the
'Alt' key together with the first letter of the respective command. For drop down
menus select the first letter of the respective command without using the 'Alt' key.
l
When using the 'play back' facility the images can be scrolled back and forth by drag-
ging the scroll bar, or using the left and right 'arrow' keys. When the results window
is active the < and > keys will scroll the images.
Language Options
Initial language settings can be set by choosing from a list of 11 languages, by
selecting 'Tools', 'Languages'.
Chinese
English
Japanese
Czech
French
Russian
Danish
German
Spanish
Dutch
Hungarian
27
Summary of Contents for CARBOLITE GERO CAF G5
