Sample Reference Information
- The upper part of this area shows the test details
such as 'Test Name', 'Test Reference', 'Acquisition date/time' and 'Analyse Date/ Time'.
The lower section controls the test piece identity number and the image number and/ or
temperature of the 'Current Selected Temperature Point' (this is shown by a green line
headed 'Current').
To show the parameters of a test piece enter the number of the test piece into the 'Test
Piece' box. This will highlight the corresponding sample grid in the sample window and
show the parameter data and the graphical data for the selected sample.
The current selected temperature point can be advanced by entering the image number
into the 'Image' box or by selecting a defined temperature point. This will also advance
the sample image in the Sample Window.
Parameter Selection
- The parameters for each individual test piece can be shown on
the graph by selecting the tick box in the graph column. Individual or all parameters can
be selected at any time. The graph key information will be shown at the right hand side
of the graph when a parameter is selected.
Deformation Selection
- The deformation temperature points can be shown on the
graph by selecting the tick box in the 'Marker ON' row under each of the deformation
point columns. Each deformation point when selected is highlighted with a magenta
coloured line which is headed with its deformation identification i.e. SST, DT, HT, FT.
Analysis Graph
- The graph shows any parameters or deformation points that have
been selected from the Parameter selection or the Deformation selections.
Note
: No graph will be shown if none of the parameters are selected.
4.7.4.9
Manual Entry of Analysis Results
To enter results manually, the manual analysis tab should be first selected.
Note
: Automatic and manual results are saved independently of each other in two
separate folders, see section 4.7.4.10.
The results table should be used in conjunction with the sample grids therefore the grids
should be activated prior to opening the Results Form, see section 4.7.2.4.
To enter the selected deformation temperature for a test piece into the form, the
sample number must first be selected. The active test piece is then identified by a
highlighted blue row on the form.
The test piece number row can be activated in one of two ways:
l
Selecting a corresponding grid in the test window, i.e. if grid 2 is selected (this will be
highlighted red), row 2 on the form will be highlighted in blue.
l
Selecting the 'Active Grid' number by scrolling up and down using the up/ down
arrows or by entering a number directly into the 'Active Grid' box.
Once the test piece row has been selected the identified deformation temperatures can
be entered into the relevant columns, by simply selecting the cell which the temperature
is to be entered.
To find the relevant deformation image, the test images can be scrolled through in a
number of ways:
42
Summary of Contents for CARBOLITE GERO CAF G5
