background image

 

 

14 

MF12 3.12

 

 

Independent Zones (control method C) 

 

When this is ordered there are three independent thermocouples (instead of the four shown) 
connected to the three controllers; the words “master” and “slave” may be replaced by “centre” 

and “end”. 

7.4

 

Control by Broadcast comms (control method B) 

 

When this is ordered there are three independent thermocouples (instead of the four shown) 
connected to the three controllers; the controllers are linked together (not shown), and remain 

“master” and “slave”. 

 

The communication between the controllers of the Eurotherm 3000 series is known as Broadcast 
comms. The wiring connections between the controllers are as follows: 

 

 

 

 

 

 

 

 

8.0

 

F

USES 

&

 

P

OWER 

S

ETTINGS

 

8.1

 

Fuses 

  

 

F1-F3: refer to the example circuit diagram.

 

F1

 

 

Internal 
supply 
fuses 

Fitted if supply cable fitted. 
Fitted on board to some types of EMC filter. 

on-board and up to 16 Amps:  
32mm x 6mm type F 
other: GEC Safeclip 

F2

 

 

Auxiliary 
circuit 
fuses 

Fitted on board to some types of EMC filter.  
May be omitted up to 25Amp/phase supply 
rating. 

2 Amps glass type F 
On board: 20mm x 5mm  
Other: 32mm x 6mm  

F3

 

 

Heat Light 
fuses 

May be omitted up to 25 Amp/phase supply 
rating. 

2 Amps glass type F  
32mm x 6mm  

 

Customer 
fuses 

Required if no supply cable fitted. 
Recommended if cable fitted. 

See rating label for amperage; 
see table below for fuse rating. 

 

Access to internal fuses is by removal of the back panel of the furnace base or control box. 

Model 

phases 

Volts 

Supply  
Rating   

Volts 

Supply  
Rating   

TZF 12/38/400  

1-phase  

200-240  

7A  

110-120 

12.5A 

TZF 12/65/550  

1-phase  

200-240  

10A  

110-120 

20A 

TZF 12/65/550  

2- or 3-phase + N 

380/220 - 415/240 

5A 

 

 

TZF 12/75/700  

1-phase  

220-240  

12.5A  

110-120 

25A  

 

TZF 12/75/700  

1-phase  

208  

15-16A  

100 

30-32A  

TZF 12/75/700  

2- or 3-phase + N 

380/220 - 415/240   7A 

 

 

TZF 12/100/900   1-phase  

200-240  

20A  

 

110-120 

40A  

 

TZF 12/100/900   2- or 3-phase + N 

380/220 - 415/240   15-16A 

 

 

other models or voltages: check the rating label for details of the supply. 

8.2

 

Power Settings 

HD 

HE 

HF 

HD 

HE 

HF 

HD 

HE 

HF 

master 

slave 

slave 

Summary of Contents for Carbolite TZF Series

















Reviews: