Z203399-0C
PAGE 1
©2012 Veris Industries USA 800.354.8556 or +1.503.598.4564 / support@veris.com
02122
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
TM
RELAYS
INSTALLATION GUIDE
Dual 10A SPDT Enclosed Relays
10-30 VDC/AC or 120 VAC Coil
Installer’s Specifications
Operating Temperature -40°C to 55°C (-40° to 131°F)
Operating Humidity
10-90% non condensing
Expected Relay Life
Electrical (at rated current): 100,000 cycles
Mechanical
(unpowered): 10,000,000 cycles
Relay Status
LED ON=energized
Wire Specifications:
Lead Length
14” (356mm) min.
Gauge
UL1015; Coil: 18 AWG; Contacts: 16 AWG
Insulation Class
600 VAC RMS
Agency Approvals
UL508 enclosed device listing
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
• Follow safe electrical work practices.
See NFPA 70E in the USA, or applicable local codes.
• This equipment must only be installed and serviced by qualified electrical personnel.
• Read, understand and follow the instructions before installing this product.
• Turn off all power supplying equipment before working on or inside the equipment.
• Use a properly rated voltage sensing device to confirm power is off.
DO NOT DEPEND ON THIS PRODUCT FOR VOLTAGE INDICATION
Failure to follow these instructions will result in death or serious injury.
DANGER
V100D
V100D
DIMENSIONS
NOTICE
• This product is not intended for life or safety applications.
• Do not install this product in hazardous or classified locations.
• The installer is responsible for conformance to all applicable codes.
• Mount this product inside a suitable fire and electrical enclosure.
INSTALLATION
Disconnect and lock out all power sources before beginning the
installation.
1. Using the threaded nipple connect the relay to the desired enclosure through a
knock out hole.
2. Secure with the conduit nut provided.
Relay #1
3. Connect Coil:
•
Choose the coil common lead (white with yellow stripe) and connect it to
the (-) source termination point.
•
Choose either the low voltage (10-30VAC/DC, white with blue stripe) or
high voltage (120VAC, white with black stripe) lead, depending on the
application requirements, and connect it to the (+) source termination
point.*
NOTE: When connecting the control side of this device (#18 wires) to power
line circuits, provide current limiting at 7 amps max.
4. Connect Relay Contacts:
•
Choose the relay common wire (yellow) and connect to switched load.
Relay #2
5. Connect Coil:
•
Choose the coil common lead (white with violet stripe) and connect it to
the (-) source termination point.
•
Choose either the low voltage (10-30VAC/DC, grey with white stripe)
or high voltage (120VAC, white with red stripe) lead, depending on the
application requirements, and connect it to the (+) source termination
point.*
NOTE: When connecting the control side of this device (#18 wires) to power
line circuits, provide current limiting at 7 amps max.
6. Connect Relay Contacts:
•
Choose the relay common wire (violet) and connect to switched load.
•
Choose the relay N.O. (brown) and/or* N.C. (grey) lead and connect to
switched load.
7. Secure the enclosure and reconnect power.
* Isolate or insulate all non-terminated wires according to local electrical code requirements, i.e.
wire nut.
2.0"
(52 mm)
2.5"
(64 mm)
3/4" NPT Nipple
2.3"
(59 mm)
4.0"
(103 mm)
3.8"
(97 mm)
