background image

Mini Tenon Cutters

 05J42.01 

– 

1

/

4

"

 05J42.05 

– 

5

/

16

"

 05J42.02 

– 

3

/

8

"

 05J42.06 

– 

 

7

/

16

"

 05J42.03 

– 

1

/

2

"

 05J42.04 

– 

9

/

16

"

Patented.

General Safety Rules

1.  Read the manual. Learn the tool’s 

applications and limitations as well as 
the specific hazards related to the tool.

2.  Use common sense. If an action 

appears to be unsafe, it likely is.

3. Wear proper eye/ear protection. 

Everyday eyeglasses have only 

 

impact-resistant lenses; they are not 
safety glasses. Also use a face or 
dust mask if the cutting operation is 
dusty. Visitors should wear the same 
protection.

4.  Wear proper apparel. Avoid wearing 

clothing with loose sleeves. Do 

not

 

wear gloves, ties, rings or bracelets 
as these can get caught in moving 
machinery.

5.  Long hair should be tied back and 

secured.

6. Do 

not

 work under the influence of 

drugs, alcohol, or medication. Drugs, 
alcohol, medication and lack of 
sleep cause impaired

  judgment and 

coordination and should not be 
combined with power tool operation.

7.  Use in an appropriate environment. 

Power tools should be used only in 
dry, clean and well-lit environments. 
Exposure to rain or use in the presence 
of flammable liquids or gases could 
result in damage or injury.

8. Do 

not

 operate electric tools in 

gaseous or explosive environments. 
The spark of the motor may cause 
the fumes to ignite.

9.  Keep workplace clean. Cluttered 

areas and benches invite 
accidents.

10. Use correct power supply. Never 

use a power source for which this 
tool was not designed. It could 
cause serious injury. If the tool is 
equipped with a three-prong plug, 
it should be plugged into a three-
hole electric receptacle. An adapter 
should be properly grounded.

11. Keep cord away from heat, oil and 

sharp edges.

12. Do 

not

 carry a plugged-in portable 

tool with finger on the switch.

Safety Rules

These safety instructions are meant to complement those that came with your 
power tool. We suggest that you reread those, in addition to those listed here 
before you begin to use this product. To use this product safely, always follow 
both sets of safety and general instructions.

2

Summary of Contents for 05J42.01









Reviews: