background image

 

ALTITUDE XXL, CORAILLE XXL 

 

2018-09 

 

Page 6 

1.4 Accessories 

The following accessories are available for the ALTITUDE XXL, CORAILLE XXL: 
 

 

TREATMENT TABLE (B12) 

If, while using your shell chair, you want to enjoy the possibility of taking your meals, writing 

or  performing  other  activities  that  require  a  working  surface,  we  offer  a  treatment  table  – 

featuring  a cut-out  for  your  abdomen  (B12)  –  that  can  be  lowered  down  to  the  side  if  not 

required, or placed on the armrest cushions by inserting the guide located under the shell 

chair into the sockets provided to that intent.  

 

 

Insert the B12 support into the sockets 

provided to this intent on the underside 

of the frame. 

 

 

Secure  the  support  to  the  underside  of 

the frame with the fixing screws. 

 

 

Insert  the  floating  axle  from  the  front 

through  the  table  sockets  and  then 

through  the  B12  support.  (To  set  the 

table  closer  to  your  body,  the  floating 

axle could also be inserted first through 

the  B12  support  and  then  through  the 

table support). 

 

 

 

l

 

A plastic washer must be placed between the table and the B12 supports. When the 

 

treatment table is removed, take care that you do not lose the washer.

 

l

 

Use the table only when seated in the upright position.

 

l

 

For proper use of the treatment table (B12): please note that the fitting can only be 

attached to the right side of the chair.

 

l

 

Before using the table, make sure that all screws have been tightened properly.

 

l

 

To prevent injury and/or damage, make sure that no objects or body parts could be 

compressed between the table and the armrest cushion.

 

l

 

To avoid injury and/or damage there should be no persons and/or objects on the right 

side of the shell chair when the board is lowered.

 

l

 

When  using  or  lowering  the  treatment  table,  the  immobilizers  must  be  engaged  to 

prevent the chair from moving on its own as a result of the movements on the chair 

as this might cause injury and/or damage.

 

l

 

Only your specialist dealer should be allowed to fit these accessories – only he has 

suitable tools and required expertise.

 

l

 

Your  warranty  claim  will  be  voided  in  the  case  of  injury  and/or  damage  due  to 

unauthorized persons having improperly fitted the accessories.

 

 

 

Summary of Contents for Coraille XXL





















Reviews: