background image

SNARE

Figure 6: SNARE instrument channel of the DRM1 MKIII

The duty of the 

SNARE

 instrument channel is apparent. However, due to its various parameters, the 

DRM1 MKIII’s snare drum is a lot more changeable than you might guess from previous analogue 
drum  machines.  The  sound  is  build  up  from  different  components:  noise,  a  needle  impulse,  a 
resonance filter and a pseudo reverb. This allows a wide spectrum of sounds ranging from short 
“clacks”, resembling old beat boxes, to compact snare sounds with noise components and additional 
reverb.

DECAY REV

  sets  the  length  of  the  reverb  effect.  This  parameter’s  effect  is  only  audible  with 

REVERB

 being enabled.

REVERB

 

adjusts the intensity of the reverb effect. With this control set fully counterclockwise, 
the reverb is disabled.

DECAY N

 

sets the release time or length of the sound’s noise component. This parameter’s 
effect is only audible with 

NOISE

 being enabled.

NOISE

 

sets  the  volume  of  the  sound’s  noise  component.  By  this,  the  snare  will  receive 
more  body  and  therefore  sounds  more  authentic.  With  this  control  set  fully 
counterclockwise, 

NOISE

 is disabled.

ATTACK

 

adds a short fixed needle impulse to the sound’s start to support its assertiveness 
on  the  one  hand,  but  is  also  used  to  initiate  oscillation  of  the  resonance  filter 
component. The audibility of the needle impulse also depends upon the intensity 
of the filter’s resonance. Always adjust 

ATTACK

 in correlation to the complete mix. 

What might appear too intrusive when being soloed might already sound too gentle 
within a full mix.

RESO

 

specifies  the  intensity  of  the  filter’s  resonance  and,  as  a  result,  colors  the  tonal 
component of the snare sound. Only at higher values, the filter will start to self-
oscillate.

FILTER

 

sets the cutoff frequency of the low pass filter. Presuming the filter has been excited 
to oscillate, this control adjusts the pitch of the snare’s tonal sound component.

14

Summary of Contents for DRM1 MKIII

























Reviews: