background image

 

Different kind of percussion sounds are possible, only by using the snare drum’s 
filter  section  but  leaving  out  the 

NOISE

  component.  With 

FILTER

  and 

RESO

 

being fully opened, the result will sound clave-like. By attenuating 

RESO

, this 

sound turns into a snare resembling a preset-beat-box from ‘78. Lowering 

FILTER

 

and combine it with different 

RESO

 settings, leads to creditable 8-toms, congas 

and bongos. (see "SNARE" on page 47)

HI HAT 1/HI HAT 2

Figure 7: HI HAT 1 instrument channel of the DRM1 MKIII - HI HAT 1 and HI HAT 2 are identical

These  two  instrument  channels  are  meant  to  create  hi-hats  but  also  cymbal  sounds.  Achieve  a 
broad spectrum of cymbals, percussions and sound effects on a basis of filtered noise and a metallic 
oscillator mixture.

DECAY

 

sets the release time or the sound’s length.

FILTER

 

sets the cutoff frequency of the low pass filter, coloring the overall sound of the 
channel.

BEND

 

adjusts the amount of a possible cutoff modulation by the 

DECAY

 envelope. In its 

central position, no modulation is present. Turn clockwise from the center position 
to  modulate  the  filter’s  cutoff  frequency,  descending  it.  Turn  counterclockwise 
from the center position will invert the modulation, resulting in an ascending cutoff 
frequency. This modulation interacts with the 

DECAY

 setting.

ATTACK

 

adds a short fixed needle impulse to the sound’s start to support the hi-hat and 
cymbals’ assertiveness. Always adjust 

ATTACK

 in correlation to the complete mix.  

The  pitch  of  the  impulse  can  be  adjusted  in  parallel  with  the  oscillator  mixture 
using 

PITCH

.

RESO

 

specifies the intensity of the filter’s resonance which, as a result, shapes the sound 
coloration of the hi-hat- and cymbal.

15

User Guide DRM1 MKIII

EN

Summary of Contents for DRM1 MKIII

























Reviews: