background image

☛ 

All of the DRM1 MKIII instrument channels offer individual outputs 

, allowing 

them to be patched to the inputs of a mixing console or an audio-interface. Find 
more details in chapter "Individual Outputs/Inserts" on page 20. 
Use the stereo 
output as a starting point.

2.  Before switching on the unit by pressing its 

POWER

 button 

, complete all audio 

connections to avoid loud impulses and cracking noises in your audio system. These peaks 
can lead to distortion and could even harm converters when connected directly to an audio-
interface. For safety reasons, while connecting and powering up the unit, turn down the 

MASTER

 control 

 of the DRM1 MKIII as well as the input controls of the units that follow 

in the signal chain. After powering up the DRM1 MKIII, the corresponding red LED next to 
the 

POWER

 button 

 will light up.

Setting up MIDI connections

1.  The unit that is supposed to trigger the DRM1 MKIII’s sounds needs to be connected to the 

DRM1’s 

MIDI IN

 jack 

. This can be a groove box, a hardware-sequencer, the MIDI output of 

a software-sequencer (using the computer’s audio- or MIDI-interface) or a keyboard.

2.

 

MIDI THRU

 

 forwards the MIDI data from the DRM1 MKIII’s MIDI input and allows 

connecting more MIDI devices in a row.

6

Summary of Contents for DRM1 MKIII

























Reviews: