background image

3

User Guide DSR-3 - dual spring reverb

EN

Important Safety Information

1.  Read these instructions.
2.  Keep these instructions. Always include these instructions when passing the product on to 

third parties.

3.  Heed all warnings and follow all instructions.
4.  Do not use this apparatus near water.
5.  Only clean the product when it is not connected to the mains power supply. Clean only with 

a dry cloth.

6.  Do not block any ventilation openings. Install in accordance with the manufacturer's 

instructions.

7.  Do not install near any heat sources such as radiators, heat registers, stoves, or other 

apparatus (including amplifiers) that produce heat.

8.  Do not defeat the safety purpose of the polarized or grounding-type plug. A polarizer plug 

has two blades and a third ground prong. The wide blade or the third prong are provided 
for your safety. If the provided plug does not fit into your outlet, consult an electrician for 
replacement of the obsolete outlet.

9.  Protect the power cord from being walked on or pinched, particularly at plugs, convenience 

receptacles, and the point where they exit from the apparatus.

10.  Only use attachments/accessories specified by VERMONA.
11.  Use only with the cart, stand, tripod, bracket, or table specified by VERMONA or sold with the 

apparatus. When a cart is used, use caution when moving the cart/apparatus combination to 
avoid injury from tip-over.

12.  Unplug this apparatus during lightning storms or when unused for long periods of time.
13.  Refer all servicing to qualified service personnel. Servicing is required when the apparatus 

has been damaged in any way, such as power supply cord or plug is damaged, liquid has been 
spilled or objects have fallen into the apparatus, when the apparatus has been exposed to rain 
or moisture, does not operate normally, or has been dropped.

14.  To completely disconnect this apparatus from the AC mains, disconnect the power supply 

cord plug from the AC receptacle.

15. 

WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain 
or moisture.

16.  Do not expose this equipment to dripping or splashing and ensure that no objects filled with 

liquids, such as vases, are placed on the equipment.

17.  The mains plug of the power supply cord shall remain readily accessible.

Summary of Contents for DSR-3



















Reviews: