Vermont Castings DBT33 Installation Instructions & Homeowner'S Manual Download

Page: 2 / 34

DBT33/DBT36/DBT39

-2-

10002789/0

ABLE

ONTENTS

Please Read The Installation & Operating Instructions Carefully Before Using The Appliance.

Important: Read all the instructions and warnings carefully before starting the installation. Failure

to follow these instructions fully may result in a possible re hazard and will void the manufacturers

warranty.

Appliance Installation instructions

Important curing/burning instructions ........................................................................................3

Locating your replace ...............................................................................................................3

Fireplace Dimensions .................................................................................................................4

Clearance to Combustibles .........................................................................................................5

Mantels........................................................................................................................................5

Hearths ........................................................................................................................................5

Framing and Finishing ................................................................................................................5

Final nishing .............................................................................................................................6

Gas Specications.......................................................................................................................6

Gas Inlet & Manifold Pressures..................................................................................................6

Gas Line Installation...................................................................................................................7

Remote Switch Installation.........................................................................................................7

Converting the Appliance Between Gas Types...........................................................................8

Venting Installation Instructions

General Venting Information - Terminal Location .....................................................................9

Connecting Direct Vent Components........................................................................................11

How To Use The Vent Graph....................................................................................................11

Vertical sidewall Applications ..................................................................................................12

Vertical sidewall Installations ...................................................................................................13

Below Grade Installations.........................................................................................................14

Vertical Through-The-Roof Applications .................................................................................15

Vertical Through-The-Roof Installations..................................................................................17

Venting Components - crimped end venting.............................................................................18

Venting Components - Twist Lock venting ..............................................................................19

Operating Instructions

Glass Warning...........................................................................................................................20

General Maintenance ................................................................................................................20

Louvre Removal .......................................................................................................................20

Glass/Frame Removal...............................................................................................................20

Glass Cleaning ..........................................................................................................................20

Installation of Logs & Lava Rock.............................................................................................21

Flame & Temperature Adjustment............................................................................................22

Flame Characteristics & Appearance........................................................................................22

Lighting Instructions.................................................................................................................23

Troubleshooting Guide .............................................................................................................24

Replacement Parts

Part Number List.......................................................................................................................26

Parts Pictorial............................................................................................................................28

Optional Accessories

EB-1 Electrical Junction Box ...................................................................................................29

Fan Kits.....................................................................................................................................29

Ceramic Refractory Lining .......................................................................................................31

Window Screen Kit...................................................................................................................31

Decorative Bay Window...........................................................................................................32

Remote Control Units ...............................................................................................................32

Warranty Imformation

...................................................................................................Back Cover

Summary of Contents for DBT33



































Search results

Summary of Contents for DBT33

Reviews:

Related manuals for DBT33

Brands by name

Popular brands

Vermont Castings DBT33, Installation Instructions & Homeowner'S Manual

Search results

Summary of Contents for DBT33

Reviews:

Related manuals for DBT33

Brands by name

Popular brands