background image

Vermont Castings  •  Defiant Flexburn 1975 Installation Manual_R1  •  2021 - ___ •  08/21

3

8390-035i

Product Listing and Important Safety Information 

A.  Appliance Certification & Efficiency Specifications

B.  Glass Specifications

This  appliance  is  equipped  with  5mm  ceramic  glass. 

Replace glass only with 5mm ceramic glass. Please contact 

your dealer for replacement glass.

Europe

Nominal heat output:

11,0 kW

CO emission (at 13% O2):

0,06%

Efficiency

81,0%

Flue gas temperature:

184,5 °C

Dust CO emission (at 13% O2):

8,9 mg/NM

3

Fuel Type:

Wood

Safety clearance distance (back):

400 mm

Safety clearance distance (side):

400 mm

Safety clearance distance (front):
Operation Type:

Intermittent

Europe - French

Puissance calorifique nominale :

11,0 kW

Émission de CO (à 13% O2) :

0,06%

Efficacité:

81,0%

Température des fumées :

184,5 °C

Émission de poussières de CO (à 13 % 

d’O2) :

8,9 mg/NM

3

Type de carburant:

Wood

Distance de sécurité (arrière):

400 mm

Distance de sécurité (côté) :

400 mm

Distance de sécurité (avant) :
Type d’opération :

Intermittent

Europe - Flemmish

Nennwärmeleistung:

11,0 kW

CO-Emission (bei 13% O2):

0,06%

Effizienz:

81,0%

Abgastemperatur:

184,5 °C

Staub-CO-Emission (bei 13% O2):

8,9 mg/NM

3

Treibstoffart:

Wood

Sicherheitsabstand (hinten):

400 mm

Sicherheitsabstand (seitlich):

400 mm

Sicherheitsabstand (vorne):
Operationstyp:

Intermittent

Japan

Nominal heat output:

11,0 kW

CO emission (at 13% O2):

0,06%

Efficiency:

81,0%

Flue gas temperature:

184,5 °C

Dust CO emission (at 13% O2):

8,9 mg/NM

3

Fuel Type:

Wood

Safety clearance distance (back):

400 mm

Safety clearance distance (side):

400 mm

Safety clearance distance (front):
Operation Type:

Intermittent

Australia

Overall  average  efficiency  burning 

hardwood When tested in accordance 

with AS/NZS 4012:

65%

Average  particulate  emission  factor 

burning  hardwood  when  tested  in 

accordance with AS/NZS 4013:

0,5 g/kg

Maximum average heat output when 

burning hardwood:

9,3 kW

Approved Fuel:

Burn only 

hardwood with a 

moisture content 

less then 25% 

(dry basis)

Wetback - All Models

Wetbacks are 

NOT an approved 

option and must 

not be fitted.

Performance may vary from test values depending 

on actual operating conditions.

Summary of Contents for Defiant FlexBurn 1975























Reviews: