6
Windsor High Efficiency Wood Stove
30005125
SO:
1. Remember to ventilate well.
2. Allow the stove to cure before burning for long periods
at high temperatures.
3. Flat spots on the painted surfaces are normal.
4. Shiny spots on the paint surface before burning is nor-
mal.
5. Call your dealer if you have any questions.
building a fire
Never use gasoline, gasoline-type latern fuel, ker-
osene, charcoal lighter fluid or similar liquids to
start or ‘freshen up’ a fire in this heater. keep all
such liquids well away from the heater while it is
in use.
inlet air control Settings
desired
inlet
**approx.
burn Setting
air Setting
btu Output
Low
Closed Fully
11,492
Med / Low
1/4 Open
11,721
Med / High
3/4 Open
15,501
High
Fully Open
18,920
1. Open inlet air control fully.
2. Place a small amount of crumpled paper in the stove.
3. Cover the paper with a generous amount of kindling in
a teepee fashion and a few small pieces of wood.
4. Ignite the paper and close door. If fire dies down sub-
stantially, open door slightly.
5. Add larger pieces of wood as the fire progresses be-
ing careful not to overload. Do not fill firebox beyond
firebrick area. An ideal coal bed of 1” to 2” should be
established to achieve optimum performance.
6. This unit is designed to function most effectively when
air is allowed to circulate to all areas of the firebox. An
ideal means of achieving this is to rake a slight (1” to
2” wide) trough in the center of the coal bed from front
to back prior to loading the fuel.
7. Once fuel has been loaded, close the door and open
air inlet control fully until fire is well established (ap-
prox. 10 minutes) being careful not to overfire.
8. Readjust air inlet control to desired burn rate. If exces-
sive smoke fills firebox, open air inlet control slightly
until flames resume and wood is sufficiently ignited.
While a basic rule of thumb is “closed-low”, “1/2 way
- medium” and “fully open-high”, refer to the Inlet Air
Control Settings chart.
9. When refueling, adjust air control to the fully open po-
sition. When fire brightens, slowly and carefully open
the door. This procedure will prevent gases from ignit-
ing causing smoke and flame spillage.
10.Add fuel being careful not to overload.
glass care
The following use and safety tips should be observed.
1. Inspect the glass regularly for cracks and breaks. If
you detect a crack or break, extinguish the fire imme-
diately and contact your dealer for replacement.
2. Do not slam door or otherwise impact the glass. When
closing doors, make sure that logs or other objects do
not protrude and impact the glass.
3. Do not clean the glass with materials which may
scratch (or otherwise damage) the glass. Scratches
on the glass can develop into cracks or breaks.
4. Never attempt to clean the glass while unit is hot. If
the deposit is not very heavy, normal glass cleaners
are adequate with a plain, nonabrasive scouring pad.
Heavier deposits may be removed with the use of a
readily available oven cleaner.
5. Never put substances which can ignite explosively in
the unit since even small explosions in confined areas
can blow out the glass.
6. This unit has an airwash system, designed to reduce
deposits on glass.
Replace glass only with high temperature Robax
pyroceram of the proper size and thickness.
gasket Replacement
After extensive use, the sealing material which provides
glass and door seal may need to be replaced if it fails to
sustain its resilience. Inspect glass and door seal periodi-
cally to ensure for proper seal. If gaskets become frayed
or worn, replace immediately.
Contact your dealer for approved replacement parts.
The following steps should be followed for glass gasket
replacement:
1. Ensure appliance is not in operation and has thor-
oughly cooled.
2. Remove screw and glass clip.
3. Lift glass out from glass clip.
4. Remove old gasket and clean glass.
5. Replace new gasket starting at the bottom of glass
working along edges, being sure to center gasket
channel on glass.
6. Trim to length and butt ends together.
