background image

5

installation

PROXIMITY TO SIDE CABINETS

1.  This range may be installed directly adjacent to existing 36" (914 mm) high base 

cabinets.

Range  dimensions:

• width: 23” 7/8 (606.5 mm)
• depth: 24” 11/64 (614.1 mm)   

 

  

 

 

 

• height (without backguard): MIN 35” 17/32 (902.5 mm) - MAX 36”  7/32 

(920 mm) 

• backguard (height): 4” 7/16 (113 mm)

Grounded outlet should be located  7” 9/32 (185 mm) from the floor and from the 

rear left to the rear right side of the range.

2.  The  range  CANNOT  be  installed  directly  adjacent  to  sidewalls,  tall  cabinets,  tall 

appliances, or other side vertical surfaces above 36” (914 mm) high. 

  There must be a minimum of 3” (76 mm) side clearance from the  range  to such 

combustible surfaces TO THE LEFT above the 36” (914 mm) high countertop; or 

there must be a minimum of 3” (76 mm) side clearance from the  range  to such 

combustible surfaces TO THE RIGHT above the 36” (914 mm) high countertop. 

  IMPORTANT: One side (left or right) above the 36” (914 mm) high countertop 

must always be kept clear. 

 

3. The maximum upper cabinet depth recommended is 13” (330 mm). Wall cabinet 

above the range must be a minimum of 30” (762 mm) above the countertop for a 

width of minimum 24” (609.6 mm): it has to be centred with the range. Side wall 

cabinets above the range  must be a minimum of 18” (457 mm) above the coun-

tertop.

4" 7/16

(113 mm)

(606.5 mm)

23" 7/8

24" 11/64

MIN 35" 17/32 (902.5 mm)

MAX 36" 7/32 (920 mm)

(614.1  mm)

Fig. 1.1

Fig. 1.2

ELECTRIC CONNECTION

(185 mm)

7" 9/32

Dotted line showing the position

of the range when installed

Area for electric connection

Summary of Contents for VEFSEE 244 P Series

















Reviews: