3-3
39014-03 06/16
VERSALIFT VST-36/40/47/52-I
SPECIFICA
TIONS
be used in conjunction with the rear torsion bar to
reduce the amount of ballast needed.
BACKUP PUMP
- An auxiliary hydraulic pump
designed to bring the booms down in case the main
hydraulic source fails. The back up hydraulic pump
is driven by a DC motor, which is powered by the
truck-engine battery. The system is connected in
parallel with the main pump and is designed for non-
continuous operation. An air cylinder at the upper
controls and a toggle switch at the pedestal are used
to energize the system.
SECOND SET OF TOOL POWER PORTS
- A
second set of tool power ports are installed at the
platform to accommodate a second open center tool.
EXTRA CONTROL CIRCUIT
- Consists of an
additional air cylinder at the platform, toggle switch
at the pedestal, pressure switch in the turret and
airline to the platform. An additional pass in the
collector ring is required for each control circuit.
MANUAL THROTTLE CONTROL
- Gives the
operator a choice of economical engine idle speeds
or faster engine speeds with faster lift movements
when required. The manual throttle control is
designed to operate only when the truck engine is
running and the master control is activated. An air
cylinder at the platform or a toggle switch at the
pedestal can be used to energize the manual throttle
control.
UNITROL 4-FUNCTION CONTROL
- The 4-Axis
controller option is a full pressure control. Located at
the platform, the 4-axis control consists of a single
handle control which, through linkage, actuates the
interlock section and four individual boom function
valves.
TRUGUARD
- This advanced upper controls isolation
system provides 4" of electrical isolation from the
entire upper controls, including the control dash
panel. This system also includes a protective shield
which helps prevent environmental and work related
contaminants from making direct contact with the
isolating surfaces.
CATEGORY D DIELECTRIC TESTING AND
CERTIFICATION -
Testing and certification for ANSI
A92.2 Category D are available. These aerial devices
which are designed and manufactured for work in
which the insulating system is not considered as
primary insulation, but secondary. These aerial
devices are NOT designed for gloving work methods.
They are rated at voltages of 46kv.
REMOTE LOWER CONTROL -
This option allows
remote operation of the aerial device. The remote
lower controls override the upper controls and are
housed in a weather-resistant hand held box or metal
box.
PLATFORM VARIATIONS
:
24 in. x 24 in. (0.61 m x 0.61 m) Fiberglass Platform
(Standard)
24 in. x 30 in. (0.61 m x 0.76 m) Fiberglass Platform
24 in. x 42 in. (0.61 m x 1.07 m) Fiberglass Platform
24 in. x 48 in. (0.61 m x 1.22 m) Fiberglass Platform
36 in. x 60 in. (0.91 m x 1.52 m) Aluminum Walk-In
Platform (Reduces maximum platform capacity by
100 lbs.) This option requires Category D rating.
40 in. x 64 in. (1.02 m x 1.55 m) Aluminum Walk-In
Platform (Reduces maximum platform capacity by
100 lbs.) This option requires Category D rating.
PLATFORM COVER
- Vinyl covers are available for
the platforms.
PLATFORM LINER
- Platform liners are available
for each of the platforms.
LIFTING EYE
- A lifting eye attachment near the end
of the outer boom has a 1000 lbs. (455 kg) maximum
capacity. (Not available on the VST-36-I)
PEDESTAL HEIGHT VARIATIONS
– Various height
pedestals are available to accommodate different
cab heights and mounting locations. See the detailed
Dimensional Specifications below for the available
and standard pedestal heights of each model.
MANUAL JIB AND WINCH -
The material handling
jib and winch consists of a winch and a jib pole that
are automatically leveled with the platform. Up to
1000 lbs. (454 kg) material handling capacity can
be provided at elevated boom angles. The winch is
hydraulically powered through a self-locking worm
gear drive, so a load-holding brake is not required.
The winch provides line speeds of 15 to 30 ft. per
minute (5 to 9 m per min.). Eighty feet (24 m) of 1/2-
in. (13 mm) diameter polyester rope with a clevis hook
THE UPPER CONTROLS DO NOT PROVIDE
PROTECTION IN THE EVENT OF ELECTRICAL
CONTACT AND ARE NOT A SUBSTITUTE FOR
MINIMUM APPROACH DISTANCES, COVER-
UPS, RUBBER GLOVES AND OTHER
PERSONAL PROTECTIVE EQUIPMENT.
Summary of Contents for VST-36-I
