background image

 

 
 
 

 
 

 

 
Copyright 1991, 1992, 1993, 1996, 1998, and 2000 Versus Technology, Inc., all rights reserved.

 

 

This document contains user’s information on technology that is proprietary to Versus Technology, Inc. 
Permitted transmittal, receipt, or possession of this document does not express license or imply any rights to use, 
sell, design, or manufacture this information. No reproduction, publication or disclosure of this information, in 
whole or in part, shall be made without prior written authorization from an officer of Versus Technology, Inc.   
 

WARNING!

 This product is not designed, intended, authorized or warranted for use in any life support or 

other application where product failure could cause or contribute to personal injury, death, or severe 
property damage. This product or its systems are covered by one or more of the following U.S. Patents: 
4,906,853; 5,017,794; 5,027,314; 5,119,104; 5,276,496; 5,355,222; 5,387,993; 5,548,637; 5,572,195, 
6,104,295. 
 

FCC STATEMENT: 

 Components complying with part 15 of the FCC Rules – Operation is subject to the 

following two conditions:  1) This device may not cause harmful interference, and 2) this device must 
accept any interference received, including interference that may cause undesired operation. 
 
Modifying or tampering with the transceiver’s or receiver’s internal components can cause a malfunction, 
invalidate the warranty, and will void your FCC authorization to use these products. 
 
Revision date: 1/29/2001 

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for VER-1700






















Reviews: