11
SEL-1200 I
NSTALLATION
M
ANUAL
Installation
r
Make sure that the transceiver is off. Remove the Battery
Pack, Microphone, and Antenna from the transceiver.
r
Referring to Figure 1, remove the two screws from the left
side of the transceiver.
r
Referring to Figure 2, remove the five screws from the rear
panel of the transceiver.
r
Draw off the rear panel and case from the transceiver body.
r
Referring to Figure 3 & 4, connect the supplied connection
cable between
J
1017
on the
MAIN U
NIT
and
J
2013
on the
CNTL U
NIT
, then route the connection cable as shown in the
drawing.
r
Affix the
SEL-1200
SELCALL Unit onto the
MAIN U
NIT
,
using the supplied double-sided adhesive tape, then connect
the 3-pin plug from the
SEL-1200
to
J
1013
on the
MAIN
U
NIT
(Figure 4).
r
Replace the case and rear panel with its seven screws, using
care to avoid pinching or damaging the connecting wires and
wounding the
MIC
jack.
r
Connect the Battery Pack to the transceiver.
Programming
r
Connect the Microphone Box and Programming Cable of the
SVC-1200
Service Kit to the computer’s serial port and the
transceiver’s
MIC
jack.
r
Start the
CE42
Programming Software, then upload the cur-
rent programming data from the transceiver via the “
Read
CH Data
” menu which appears when you press the ([
F4
]:
Transfer
) key.
r
Press the ([
F3
]:
Option
) key to invoke a pop-up window,
then select the “
Sel Call Unit
” item, and change its setting to
“
on
.”
r
Program the SELCALL features (such as the “
Sel Call ID
,”
“
Sel Call Memory
,” etc.), if needed.
r
Press the ([
F3
]:
Option
) key again to close the pop-up win-
dow, then turn on the SELCALL feature (on the main screen)
on the channel(s) where you wish to operate.
r
Download the revised programming data to the transceiver
from the computer via the “
Write CH Data
” menu, which
appears when you press the ([
F4
]:
Transfer
) key.
r
Installation and programming are now complete.
r
Disconnect the Programming Cable from the transceiver’s
MIC
jack.
Å
Å
Å
Å
Å
Å
Ç
J
1016
J
1017
PA UNIT
MAIN UNIT
SEL-1200
Supplied
Connection Cable
CNTL UNIT
J
2013
Supplied
Connection Cable
Figure 1
Figure 2
Figure 3
Figure 4
I
MPORTANT
N
OTE
!
Do not touch
the potentiometer nor the jumper plug of
the
SEL-1200
. The
SEL-1200
is carefully
aligned at
the factory for the specified performance.
Installation Manual Reprint
Summary of Contents for VX-1210
