background image

2

vertilux.com

© 2019. Vertilux, Ltd. All Rights Reserved. Last revised: February 2019.

Check that the motor is compatible with the associated track and accessories and that it is correctly 

installed into the end adapter 

(fig. 1)

. Be aware that the motor can be installed in any of the 2 track 

end adapters that come with the motor, also known as main and secondary control.

Initial programming sequence 

Before starting…

Optional functions 

• 

Checking the traversing direction

• 

Adding an additional remote control or “cloning” a channel

• 

Deleting a single motor or channel

• 

Deleting the motor from all channels

• 

Resetting the motor to factory default

1

Pair the motor with the remote control.

2

Operate the motor in both directions until the main 

carrier reaches one end side of the track, and then 

the opposite one, allowing the motor to automatically 

self-adjust its electronic limits.

Note:

 to remove the motor from the main control

pull the 

LOCKING BAR

 and push it to the left side.

Fig. 1.

 Sequence to install the motor into the main control

Place the motor shaft into the control and 

pull the safety

 locking bar 

downwards.

While downwards, move the 

safety

 locking bar 

to the right.

Then, release the safety 

locking bar 

to secure the motor in the control.

 

LOCKING BAR

Summary of Contents for 1-700-DM-00064





















Reviews: