9
GWARANCJA I SERWIS
Warunki gwarancji oraz opis postepowania w przypadku reklamacji
zawarte są w załączonej Karcie Gwarancyjnej.
Serwis Centralny
GTX Service
tel. +
48
22
573
0
3
85
Ul. Pograniczna
2
/
4
fax.
+
48
22
573
0
3
83
0
2
-
285
Warszawa
e-mail service@gtxservice.pl
Sieć Punktów Serwisowych do napraw gwarancyjnych
i pogwarancyjnych dostępna na platformie internetowej
gtxservice.pl
Grupa Topex zapewnia dostępność części zamiennych oraz
materiałów eksploatacyjnych dla urządzeń i elektronarzędzi.
Pełna oferta części i usług na
gtxservice.pl
. Zeskanuj kod QR i wejdź:
TRANSLATION OF THE ORIGINAL INSTRUCTIONS
TILE CUTTER
52G281
CAUTION: BEFORE USING THE DEVICE READ THIS MANUAL CAREFULLY
AND KEEP IT FOR FUTURE REFERENCE.
DETAILED SAFETY REGULATIONS
SAFETY CONDITIONS SPECIFIC FOR CERAMIC TILE SAW
•
Power supply voltage must match value marked on the rating plate
of the ceramic tile saw.
•
Connect the tile saw only to electrical system equipped with
residual current circuit breaker that will cut the power off when
earth leakage current exceeds
3
0 mA in less than
3
0 ms.
•
When working outdoors use only extension cords designed for
outdoor use.
•
During operation of the tile saw follow strictly applicable regulations
regarding occupational health and safety.
•
Make sure direction of cutting blade rotation matches indicated
direction of the saw motor.
•
Cutting blade of the saw should be free to rotate after installation.
•
Always use anti-splinter goggles, hearing protection and anti-dust mask.
•
Always wear proper clothing for your work! Loose items of clothing
or jewellery might get caught by rotating cutting blade.
•
Ensure that saw arm is well fixed before making a cut.
•
Before any adjustment, measurement, cleaning or removing
jammed ceramic pieces always disconnect power supply from the
tool with the switch and remove the plug from mains socket!
•
After repair or maintenance is carried out, install all shields and
protective parts before switching on the tile saw.
•
Do not start working with the tile saw when tired or under influence
of medicines.
•
It is vital that all persons who operate the tile saw are properly
trained for operation, using and adjustments of the tile saw.
•
Replace damaged protection parts immediately.
•
Never overload the tile saw, causing rotational speed to drop down
considerably.
•
Keep the workplace clean. Before working remove waste material
and unnecessary objects.
•
Keep bystanders away from the tile saw workplace.
•
Keep the workplace well illuminated.
•
Do not distract person who is working with the tile saw.
•
After the motor is switched off with the switch, never attempt to
stop the cutting blade by applying side pressure.
•
Immediately replace damaged cutting blade.
•
Never use cutting blades with parameters different from specified
in this manual.
•
Never attempt to remove or disconnect protection parts of the tile saw.
•
When a break in work is required, finish current cutting and switch
off the tile saw.
•
When a break in work and leaving the workplace is required, switch
off the tile saw with the switch and disconnect it from power supply
by removing the plug from mains socket.
•
Check technical condition of the tile saw before starting to operate:
–
all protection parts must be in good working order and operate
as supposed to,
–
screws and other mount parts must not be loosened,
–
all adjustment keys must be removed from the tool.
•
Always ensure the processed material adheres to the work table of
the saw with its whole surface.
•
Never cut several pieces of material at a time.
•
Do not unplug the tile saw from mains socket by pulling the cord.
Protect the power cord against excessive heat, oil and sharp edges.
•
When operating the tile saw keep your body in firm, standing position.
•
All parts of the tile saw must be properly fixed.
•
Repairs of the tile saw should only be carried out by qualified
person in authorized service workshop and with use of original
spare parts.
•
Do not make profile cuts with the tile saw.
GB
Summary of Contents for 52G281
