background image

Steering column, suspension and wheels.

 The steering column bears the handlebars,

clamped on  its  top  end,  and  the front  wheel  swinging  hub,  pivoted  at   its   bottom end

through a stub axle (see Fig. 9). 

Front suspension

 with variable rate coil spring and double action hydraulic damper. 

Rear suspension:

  swinging bracket for engine and rear wheel, variable rate coil spring

and coaxial, double action hydraulic tamper.

- The wheels are interchangeable with rims of pressed steel sheet (0 8"). 

- Tyres of dia. 3.40-8".

Saddle

  of  the  nose-pivoted,   sprung  type  with   central   spring  adjustable   to   the   driver's

weight.

Brakes.

 Expanding type with cable control. 

Front:

 lever on R. H. side of handlebars. 

Rear:

 control pedal on floorboard, R. H. Drums in light alloy with cooling fins.

Central stand.

 A two-legged stand, easy to operate, is arranged under the floorboard. A

strong return spring in the middle holds it in contact with the floorboard and keeps it from
vibrating while the scooter is being ridden.

Fig. 9 – Engine and suspension
1. Steering column and front suspension – 2. Engine – 3. Pivoting arm of crankcase half, clutch side –
4. Rear suspension spring and hydraulic shock absorber

Summary of Contents for 1962 150
































Reviews: