VESPA GTS Super 125 i.e. Service Station Manual Download

Page: 175 / 285

With the connector on the control unit side discon-

nected, and the coolant temperature sensor con-

nector connected, check that the resistance val-

ues between pins 13 and 7 correspond to the

engine temperature.

20° = 2500 ± 100

Ω

80° = 308 ± 6

Ω

With the control unit side connector disconnected,

and the coolant temperature connector discon-

nected, check the insulation between the two light

blue-green and grey-green cables.

Zeroing the throttle

Resetting the throttle valve position signal (TPS reset)

The MIU control unit is supplied with a throttle valve position sensor that is pre-calibrated.

Pre-calibration entails regulating the minimum opening of the throttle valve to obtain a certain flow of

air under pre-set reference conditions.

Pre-calibration ensures optimal air flow to control idling.

This regulation must not be tampered with in any way whatsoever.

The injection system will complete the management of the idling through the Stepper motor and the

variation of the ignition advance.

The throttle body after the pre-calibration has an opened valve with an angle that can vary depending

on the tolerances of the machining of the pipe and the valve itself.

The valve position sensor can also assume various fitting positions. For these reasons the mV of the

sensor with the valve at idle can vary from one throttle body to another.

To obtain the optimum fuel mixture, especially at small openings of the throttle valve, it is essential to

match the throttle body with the control unit following the procedure known as TPS resetting.

With this operation we inform the control unit, as the starting point, of the mV value corresponding to

the pre-calibrated position.

To reset, proceed as follows.

Vespa GTS Super 125 i.e.

Injection

INJEC - 175

Summary of Contents for GTS Super 125 i.e.






























































































































































































































































































Search results

Summary of Contents for GTS Super 125 i.e.

Reviews:

Related manuals for GTS Super 125 i.e.

Brands by name

Popular brands

VESPA GTS Super 125 i.e., Service Station Manual

Search results

Summary of Contents for GTS Super 125 i.e.

Reviews:

Related manuals for GTS Super 125 i.e.

Brands by name

Popular brands