VESPA GTS Super 125 i.e. Service Station Manual Download

Page: 47 / 285

ing can be cleaned off by removing the two rubber

caps «

».

CAUTION

IF THE VEHICLE IS USED ON DUSTY ROADS IT IS NEC-
ESSARY TO CARRY OUT MAINTENANCE CHECKS OF
THE AIR FILTER MORE OFTEN TO AVOID DAMAGING THE
ENGINE.

Recommended products

AGIP FILTER OIL

Special product for the treat-

ment of foam filters.

Engine oil

In four stroke engines, the engine oil is used to lubricate the timing elements, the bench bearings and

the thermal group.

An insufficient quantity of oil can cause serious damage to the engine.

In all four stroke engines, the deterioration of the oil characteristics, or a certain consumption should

be considered normal, especially if during the run-in period. Consumption levels in particular can be

influenced by the conditions of use (e.g.: oil consumption increases when driving at "full throttle".

Replacement

At 1,000 km and after every 10,000 km, the oil and

the filter must be changed. The engine must be

drained by running off the oil from drainage cap

" of the flywheel side gauze pre-filter; further-

more to facilitate oil drainage, loosen the cap/

dipstick "

". Once all the oil has drained through

the drainage hole, unscrew the oil cartridge filter

" and remove it.

Make sure the pre-filter and drainage plug O-rings

are in good conditions.

Lubricate them and refit the mesh filter and the oil

drainage plug, screwing them up to the prescribed

torque.

Vespa GTS Super 125 i.e.

Maintenance

MAIN - 47

Summary of Contents for GTS Super 125 i.e.






























































































































































































































































































Search results

Summary of Contents for GTS Super 125 i.e.

Reviews:

Related manuals for GTS Super 125 i.e.

Brands by name

Popular brands

VESPA GTS Super 125 i.e., Service Station Manual

Search results

Summary of Contents for GTS Super 125 i.e.

Reviews:

Related manuals for GTS Super 125 i.e.

Brands by name

Popular brands