VESPA GTS Super 125 i.e. Service Station Manual Download

Page: 90 / 285

KEY

. Battery

. Fuse No. 1

. Fuse No. 5

. Ignition switch contacts

. Fuse No. 4

. Fuse No. 7

. Electronic control unit

. Daylight running light bulbs and license plate light

. High/low beam two-light bulb

. Light switch

. Headlight relay

WARNING

ALL CONTINUITY TESTS MUST BE CARRIED OUT WITH THE CORRESPONDING CONNECTORS
DISCONNECTED.

TAIL LIGHTS AND LICENSE PLATE LIGHT LINE

1) Check that bulbs operate properly.

2) Check fuses No. 1 and 7.

3) Check key switch contacts.

4) Check if there is voltage between the Yellow-Black cable of fuse No. 7 and the ground. If not, check

cable harnesses.

5) Check that the cable harnesses of the bulbs and their ground connection are not interrupted.

HIGH-BEAM /LOW-BEAM LIGHTS LINE

1) Check that bulbs operate properly.

2) Check fuses No. 1, 4 and 5.

3) Check key switch contacts.

4) Check if there is voltage between the Grey cable of the headlight remote control and the ground

connection. If there is not, check the cable harnesses.

5) With the key switch set to «

» and the engine running, check if there is voltage between the Yellow-

Red cable of the headlight remote control and the ground connection. If there is not, check the cable

harnesses.

6) Check that the White-Black cable connecting the headlight remote control switch and the control unit

(pin 19) is not interrupted.

7) Check the headlight remote control switch.

8) Check that the Grey-Red cable of the light switch and the headlight remote control switch is not

interrupted.

9) Check the light switch contacts.

10) Check that the cable harnesses of the bulbs and their ground connection are not interrupted.

Electrical system

Vespa GTS Super 125 i.e.

ELE SYS - 90

Summary of Contents for GTS Super 125 i.e.






























































































































































































































































































Search results

Summary of Contents for GTS Super 125 i.e.

Reviews:

Related manuals for GTS Super 125 i.e.

Brands by name

Popular brands

VESPA GTS Super 125 i.e., Service Station Manual

Search results

Summary of Contents for GTS Super 125 i.e.

Reviews:

Related manuals for GTS Super 125 i.e.

Brands by name

Popular brands